EasyManuals Logo

Mitsubishi QD75M1 User Manual

Mitsubishi QD75M1
882 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #195 background imageLoading...
Page #195 background image
5 - 108
MELSEC-Q
5 DATA USED FOR POSITIONING CONTROL
Da.15
Condition target
Set the condition target as required for each control.
Setting value Setting details
01
H
: Device X
02
H
: Device Y
Set the input/output signal ON/OFF as the conditions.
03
H
: Buffer memory (1-word)
04
H
: Buffer memory (2-word)
Set the value stored in the buffer memory as the condition.
03
H
: The target buffer memory is "1-word (16 bits)"
04
H
: The target buffer memory is "2-word (32 bits)"
05
H
: Positioning data No. Select only for "simultaneous start".
Da.16
Condition operator
Set the condition operator as required for the "
Da.15
Condition target".
Da.15
Condition target
Setting value Setting details
07
H
: DEV=ON 01
H
: Device X
02
H
: Device Y
08
H
: DEV=OFF
The state (ON/OFF) of an I/O signal is defined as the
condition. Select ON or OFF as the trigger.
01
H
:
∗∗
=P1
02
H
:
∗∗
≠
P1
03
H
:
∗∗≤
P1
04
H
:
∗∗
≥
P1
05
H
: P1
≤∗∗≤
P2
03
H
: Buffer memory (1-word)
04
H
: Buffer memory (2-word)
06
H
:
∗∗≤
P1, P2
≤∗∗
Select how to use the value (
∗∗
) in the buffer memory
as a part of the condition.
10
H
: Axis 1 selected
20
H
: Axis 2 selected
30
H
: Axes 1 and 2 selected
40
H
: Axis 3 selected
50
H
: Axes 1 and 3 selected
60
H
: Axes 2 and 3 selected
70
H
: Axes 1, 2, and 3 selected
80
H
: Axis 4 selected
90
H
: Axes 1 and 4 selected
A0
H
: Axes 2 and 4 selected
B0
H
: Axes 1, 2, and 4 selected
C0
H
: Axes 3 and 4 selected
D0
H
: Axes 1, 3, and 4 selected
05
H
: Positioning data No.
E0
H
: Axes 2, 3, and 4 selected
If "simultaneous start" is specified, select the axis
(or axes) that should start simultaneously.
Da.17
Address
Set the address as required for the "
Da.15
Condition target".
Da.15
Condition target
Setting value Setting details
01
H
: Device X
02
H
: Device Y
– Not used. (There is no need to set.)
03
H
: Buffer memory (1-word)
04
H
: Buffer memory (2-word)
Value
(Buffer memory address)
Set the target "buffer memory address".
(For 2 word, set the low-order buffer memory
address.)
05
H
: Positioning data No. – Not used. (There is no need to set.)

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Mitsubishi QD75M1 and is the answer not in the manual?

Mitsubishi QD75M1 Specifications

General IconGeneral
BrandMitsubishi
ModelQD75M1
CategoryController
LanguageEnglish

Related product manuals