Mitsubishi QD75M1 User Manual

Index - 6
JOG start signal............................................. 3-15
JUMP instruction ......................................... 9-111
[K]
kPPS (Explanation of positioning terms)
..........................................................Appendix-80
[L]
Last executed positioning data No. (
Md.46
)
..................................................................... 5-132
LED display functions................................ 15-106
LEND ........................................................... 9-114
Limit switch (Explanation of positioning terms)
..........................................................Appendix-80
Linear interpolation (Explanation of positioning
terms)................................................Appendix-81
List of block start data ................................... 5-98
List of condition data ................................... 5-104
List of configuration devices............................ 2-4
List of control data....................................... 5-138
List of dedicated instructions......................... 14-2
List of devices used......................................... 6-5
List of errors................................................... 15-6
List of functions................................................ 3-4
List of input/output signal details................... 3-18
List of input/output signals ............................ 3-12
List of monitor data...................................... 5-110
List of parameters.......................................... 5-22
List of positioning data .................................. 5-82
List of warnings ........................................... 15-90
Load inertia (
Pr.112
).................................... 5-64
Load inertia ratio (Explanation of positioning
terms)................................................Appendix-81
LOOP........................................................... 9-113
Lower limit...................................................... 3-18
Low-inertia motor (Explanation of positioning
terms)................................................Appendix-81
[M]
M code (Condition data No., No. of LOOP to
LEND repetitions) (
Da.10
) ......................... 5-94
M code (Explanation of positioning terms)
..........................................................Appendix-81
M code OFF request ................................... 12-65
M code OFF request (
Cd.7
) .................... 5-140
M code ON signal.......................................... 3-13
M code ON signal output timing..................12-64
M code ON signal output timing (
Pr.18
) ...5-30
M code output function ................................12-64
Machine feed value........................................9-16
Machine feed value (
Md.21
).....................5-120
Machine feed value (Explanation of positioning
terms) ................................................Appendix-81
Machine OPR...................................................8-4
Machine response suppression filter (
Pr.118
)
........................................................................5-66
Machine response suppression filter 2 (
Pr.161
)
........................................................................5-80
Main functions..................................................3-6
Major positioning controls................................9-2
Manual control ...............................................11-2
Manual pulse generator...................................2-4
Manual pulse generator................................ A-14
Manual pulse generator (Explanation of
positioning terms)..............................Appendix-81
Manual pulse generator 1 pulse input
magnification (
Cd.20
) ...............................5-150
Manual pulse generator enable flag (
Cd.21
)
......................................................................5-150
Manual pulse generator input selection (
Pr.24
)
........................................................................5-32
Manual pulse generator operation ..............11-27
Manual pulse generator operation program
........................................................................6-42
Manual pulse generator operation start time chart
......................................................................11-34
Manual pulse generator operation timing and
processing times..........................................11-29
Master axis (Explanation of positioning terms)
...........................................................Appendix-81
Mechanism of positioning control....................1-7
Monitor data area.............................................7-3
Movement amount after near-point dog ON
(
Md.34
)......................................................5-128
Monitor output 1 offset (
Pr.127
) ..................5-74
Monitor output 2 offset (
Pr.128
) ..................5-74
Motor capacity (
Pr.104
) ..............................5-60
Motor current value (
Md.104
) ....................5-134
Motor rotation speed (
Md.103
) .................5-134
Motor type (
Pr.103
) .....................................5-60

Mitsubishi QD75M1 Specifications

General

Brand	Mitsubishi
Model	QD75M1
Category	Controller
Language	English