Mitsubishi QD75M1 User Manual

Index - 7
Monitor output offset (
Pr.127
) .................... 5-74
Movement amount per pulse (
Pr.2
to
Pr.4
)
....................................................................... 5-22
Movement amount per pulse (Explanation of
positioning terms).............................Appendix-82
Movement amount per rotation (
Pr.3
)...... 5-22
Multi-phase pulse (Explanation of positioning
terms)................................................Appendix-82
Multiple axes simultaneous start control .... 10-20
Multiple PLC .................................................... 2-5
Multiplying rate setting (Explanation of positioning
terms)................................................Appendix-82
[N]
Names of each part......................................... 4-3
NC language (Explanation of positioning terms)
..........................................................Appendix-82
Near pass function ...................................... 12-20
Near pass .................................................... 12-20
Near-point dog (Explanation of positioning terms)
..........................................................Appendix-82
Near-point dog method machine OPR ........... 8-6
Near-point dog signal.................................... 3-18
New acceleration time value (
Cd.10
) ...... 5-144
New current value ....................................... 9-105
New current value (
Cd.9
)......................... 5-142
New current value (Explanation of positioning
terms)................................................Appendix-82
New deceleration time value (
Cd.11
)...... 5-144
New speed value (
Cd.14
)........................ 5-146
New torque value (
Cd.22
)........................ 5-150
NEXT start................................................... 10-15
No. of control axes .......................................... 3-2
No. of modules can be mounted..................... 2-5
No. of occupied I/O points............................... 3-3
No. of pulses per rotation (
Pr.2
) ............... 5-22
No. of write accesses to flash ROM (
Md.19
)
..................................................................... 5-118
NOP instruction ........................................... 9-110
Normal start................................................... 10-8
[O]
OP (Explanation of positioning terms)
..........................................................Appendix-83
OP address (
Pr.45
)................................... 5-50
OP shift amount (
Pr.53
).............................5-56
OP shift function.............................................12-8
OP shift function (Explanation of positioning terms)
...........................................................Appendix-83
Operating principle...........................................1-7
Operation pattern (
Da.1
) ............................5-84
Operation pattern (Explanation of positioning
terms) ................................................Appendix-83
Operation patterns...........................................9-5
Operation timing and processing time during
position-speed switching control ...................9-93
Operation timing and processing time during
speed-position switching control (ABS mode)
........................................................................9-93
Operation timing and processing time during
speed-position switching control (INC mode)
........................................................................9-85
Operation timing and processing time of fast OPR
........................................................................8-14
OPR acceleration time selection (
Pr.51
) ..5-54
OPR basic parameters ..................................5-48
OPR complete flag.......................................5-126
OPR deceleration time selection (
Pr.52
) ..5-54
OPR detailed parameters..............................5-54
OPR direction (
Pr.44
)................................5-50
OPR method ....................................................8-5
OPR method (
Pr.43
)..................................5-48
OPR method (1): Near-point dog method.......8-6
OPR method (2): Count method 1)
..........................................................................8-8
OPR method (3): Count method 2)
........................................................................8-10
OPR method (4): Data set method ...............8-12
OPR method (Explanation of positioning terms)
...........................................................Appendix-83
OPR OFF request program...........................6-35
OPR parameter (Explanation of positioning terms)
...........................................................Appendix-83
OPR request ....................................................8-2
OPR request (Explanation of positioning terms)
...........................................................Appendix-84
OPR request flag .........................................5-126
OPR request flag OFF request (
Cd.19
)
......................................................................5-150
OPR retry (
Pr.48
).......................................5-52
OPR re-travel value (
Md.100
)....................5-134

Mitsubishi QD75M1 Specifications

General

Brand	Mitsubishi
Model	QD75M1
Category	Controller
Language	English