Mitsubishi RCN-E2 User Manual

-
6
-
WIRELESS REMOTE CONTROL HANDLING
PROCEDURE
REPLACING THE BATTERIES
If the following occurs, the batteries are exhausted. Replace
them with new ones.
•
When the signal is transmitted, the air conditioner does not
display reception.
•
The display fades away or does not show anything.
■
How to insert batteries
1 Detach the back lid.
2 Insert the batteries. (two AAA batteries)
3 Reattach the back lid.
4 Adjust the current time.
Pay attention to the
and marks
SETTING AFTER BATTERY REPLACEMENT
•
When batteries are replaced, the remote control setting,
indoor function setting, and time display are reset to the
default. After replacing batteries, set them again to the
preferred settings.
Change remote control setting
Function Description Switching method
Operation
mode
AUTO
Switches the AUTO
mode between
Enable and Disable.
MODE
button
While holding down each
button, turn the power on or
press the ACL switch.
Indoor function settings (page 10) / CURRENT TIME
SETTING PROCEDURE (page 8)
ABOUT BATTERIES
•
The recommendable effective period of a battery is about 6
to 12 months.(It depends on the usage.)
•
The recommendable effective period is printed on the
battery. This may be shorter due to manufacturing time of
the unit.
However the battery may be still working in order after
expiry date.
•
The batteries packaged with the remote control are
supplied in order to check operating conditions when
usage begins, and subsequently, the life of these batteries
may be shorter than that of new batteries.
ATTENTION
•
When replacing batteries, replace with two new AAA
batteries at the same time. (Alkaline batteries are
recommended.)
•
Do not mix old and new batteries or types of batteries (for
example, manganese and alkaline batteries).
•
Do not use rechargeable batteries.
CAUTION CAUTIONS ON SWITCH OPERATIONS
ACL
•
When operating the “FUNCTION SETTING”, “TIME SET
UP”, or “ACL” switches, press it straight downward using an
object with a short pointed end such as a ballpoint pen.
Do not press those switches forcefully at an angle using an
object with a long and sharp end such as a mechanical
pencil. Otherwise, the buttons may not pop up to their
original positions.
HOW TO OPERATE
•
If you press each button on the wireless remote control
while pointing it at the signal receiver of the air conditioner
body, a signal is sent. When the signal has been received
without a problem, the RUN indicator LED blinks.
ATTENTION
•
The buttons on the remote control must be operated
carefully and securely.
If an error occurs on the display of the remote control
•
Press the ACL switch with a ballpoint etc.
Press the ACL switch to reset to the time set up mode. Set
the time correctly.
ABOUT REMOTE CONTROL HOLDER
•
The remote control can be mounted on the wall or pillar
with the remote control holder.
Slide from the upper part of the holder to place or take out
the remote control.
ATTENTION
•
If the remote control signal receiver is exposed to direct
sunlight or strong light, the receiver may not be able to
receive a signal. In this case, block the sunlight or dim the
light.
•
Do not block the signal between the remote control and the
remote control signal receiver.
•
Do not point the air conditioner wireless remote control at
devices such as a TV set that have their own wireless
remote control.
•
The remote control must be handled carefully.
•
Remove the batteries when the remote control is not used
for a long time.
•
Even if the remote control is not found or damaged, you
can operate the air conditioner with itself. See “10.
BACKUP SWITCH OPERATION” on page 10.
PJZ012A128_EN.indd 6PJZ012A128_EN.indd 6 11/10/2016 6:53:20 PM11/10/2016 6:53:20 PM

Mitsubishi RCN-E2 Specifications

General

Brand	Mitsubishi
Model	RCN-E2
Category	Remote Control
Language	English