EasyManua.ls Logo

MJX Bugs 3 Pro - Aircraft Status and Initialization; Aircraft Status Indicators; Aircraft Initialization Detection

MJX Bugs 3 Pro
21 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Aircraft status indicator
No
Indicator status
Meanings
1
Front and rear lights flash yellow rapidly.
Aircraft 2.4GHz disconnected.
2
Front and
rear
lights flash red, green and
y ell ow alternatively
Aircraft is in initialization detection status.
3
Front lights glow solid
red, rear lights glow
solid green.
No GPS signal, aircraft is in gesture mode.
4
Front light glows solid red, rear
light glows solid green.
Good GPS signal, aircraft is preparing
for GPS mode.
5
Front and rear lights flash green rapidly.
Aircraft is in gyroscope calibration status.
6
Front and rear lights flash yellow alternatively.
Aircraft is in compass horizontal calibration.
7
Front and rear lights flash green alternatively.
Aircraft is in compass vertical calibration.
8
Front light
glows solid rec .
rear light
flashs rec.: slowly.
Aircraft is nearly low voltage, 114
battery level left.
9
Front light
glo'ws solid rec •
rear light
flashes red
rapidly.
Aircraft is in low voltage, only 1/6
voltage left.
10
Front and rear lights
flash
once, stop
for 1.5 second.
Something wrong with the gyroscope.
11
Front and rear lights flash twice, stop
for 1.5 second.
Something wrong with the barometer.
12
Front and rear lights flash three times, stop
for 1.5 second.
Something wrong with the compass.
13
Front and rear lights flash fourth times, stop
for 1.5 second.
Something wrong with the GPS module.
Aircraft initialization detection
After signal connection, the aircraft enters into initialization detection procedure with front and rear
lights flashing red, green and yellow alternatively. Make sure that the aircraft is set on a flat and still
surface for the initialization detection. The aircraft initialization detection takes about 8 seconds. Once
the remote controller sends out "Di
Di"
sounds and the aircraft front and rear lights flash yellow
alternatively, initialization detection is completed.
Attention: Make sure that the aircraft is set on a flat and still surface for the initialization
detection.
Aircraft status indicator
No
Indicator status
Meanings
1
Front and rear lights flash yellow rapidly.
Aircraft 2.4GHz disconnected.
2
Front and
rear
lights flash red, green and
y ell ow alternatively
Aircraft is in initialization detection status.
3
Front lights glow solid
red, rear lights glow
solid green.
No GPS signal, aircraft is in gesture mode.
4
Front light glows solid red, rear
light glows solid green.
Good GPS signal, aircraft is preparing
for GPS mode.
5
Front and rear lights flash green rapidly.
Aircraft is in gyroscope calibration status.
6
Front and rear lights flash yellow alternatively.
Aircraft is in compass horizontal calibration.
7
Front and rear lights flash green alternatively.
Aircraft is in compass vertical calibration.
8
Front light
glows solid rec .
rear light
flashs rec.: slowly.
Aircraft is nearly low voltage, 114
battery level left.
9
Front light
glo'ws solid rec •
rear light
flashes red
rapidly.
Aircraft is in low voltage, only 1/6
voltage left.
10
Front and rear lights
flash
once, stop
for 1.5 second.
Something wrong with the gyroscope.
11
Front and rear lights flash twice, stop
for 1.5 second.
Something wrong with the barometer.
12
Front and rear lights flash three times, stop
for 1.5 second.
Something wrong with the compass.
13
Front and rear lights flash fourth times, stop
for 1.5 second.
Something wrong with the GPS module.
Aircraft initialization detection
After signal connection, the aircraft enters into initialization detection procedure with front and rear
lights flashing red, green and yellow alternatively. Make sure that the aircraft is set on a flat and still
surface for the initialization detection. The aircraft initialization detection takes about 8 seconds. Once
the remote controller sends out "Di
Di"
sounds and the aircraft front and rear lights flash yellow
alternatively, initialization detection is completed.
Attention: Make sure that the aircraft is set on a flat and still surface for the initialization
detection.

Related product manuals