modec MC89 - Page 10

10
Performances & technical characteristics
Straight or with RA30
Free speed
(rpm)
Max torque
(Nm (lb.ft))
Weight kg (lb)
Dimensions (l x d x
h) mm (in)
MC89E-007
450
115 (85)
5,1 (11.2)
354 x 96 x 269
(13.9”x3.78”x10.6”)
MC89S-035
94
550(400)*
5,1 (11.2)
354 x 96 x 269
(13.9”x3.78”x10.6”)
MC89S-054
61
850(630)*
5,4 (11.9)
367 x 96 x 269
(14.4”x3.78”x10.6”)
* Warning ! Do not use the RA30 right angle head with a torque > 600 Nm (440 lb.ft), use the torque limiter
(see table below) All performance values indicated above have a +/-5% accuracy
Use with a Banjo head
Banjo heads enable to use the actuator on a handwheel with a rising stem. They also
add a gear ratio to the system by reducing the speed and increasing the torque by 4
for the BJH01 and by 3 for the BJH02. However, the BJH01 cannot withstand an output torque
higher than 600 Nm (440 lb.ft). As a consequence, the input torque should not exceed 150 Nm
(110 lb.ft). The BJH02 cannot withstand an output torque higher than 1000 Nm (740 lb.ft). As
a consequence, the input torque should not exceed 330 Nm (240 lb.ft).
When using a Banjo head, it is essential to set the electronic torque limiter so that the input
torque will not exceed 150 Nm (110 lb.ft) for the BJH01 and 1000 Nm (740 lb.ft) for the BJH02.
Failure to observe these precautions can lead to premature aging of the banjo head and even
breakage.
With Banjo head
BJH01
Free speed
(rpm)
Max torque
(Nm (lb.ft))
MC89E-007
113
460 (340)
MC89S-035
24
600 (440)*
MC89S-054
14
600 (440)*
* Warning ! The maximum acceptable torque for the BJH01 is 600 Nm (440 lb.ft). Do not use the BJH01 if
the torque required is higher than 600 Nm (440 lb.ft), use the torque limiter to limit the input torque to 150
Nm (110 lb.ft) (see stickers on the actuator and table hereafter)
With Banjo head
BJH02
Free speed
(rpm)
Max torque
(Nm (lb.ft))
MC89E-007
150
350 (260)
MC89S-035
31
1000 (740)*
MC89S-054
20
1000 (740)*
* Warning ! The maximum acceptable torque for the BJH02 is 1000 Nm (740 lb.ft). Do not use the BJH02 if
the torque required is higher than 1000 Nm (740 lb.ft), use the torque limiter to limit the input torque to
330 Nm (240 lb.ft) (see stickers on the actuator and table hereafter)
Sound and vibration levels
Sound and vibration levels are calculated based on the conditions of use at the maximum rated
speed. Values apply to the core tool (without added options or accessories). The values can vary
significantly depending on the equipment to which the tool is applied. The end operator should
establish the actual measurements.
Maximum level of weighted acoustic pressure A at the operator’s location
L
PA
= 73 dB(A)
Maximum level of weighted acoustic power A at the operator’s location
L
WA
= 84 dB(A)