www.miinet.comMoore Industries-International, Inc.
- 51 -
User’s Manual
238-741-00K
May 2019
Programmable Smart HART Temperature Transmitter
THZ
3
/ TDZ
3
SECTION 4
Figure 4.1. TDZ
3
or THZ
3
Configuration Online menu overview
Online Menu
Mode l
Device Setup
PV is
PV Quality
PV
PV Loop Cu rrent
PV LRV
PV URV
SV
TV
QV
Range Alarm
Status*
Process
Variables
Setup
Custom
Calibraon
Review
PV
PV Quality
PV Loop Current
PV is
PV Damping
PV % rnge
Dynami c
Variables
Device
Variables
PV
PV Quality
PV is
SV
SV Quality
SV is
TV
TV Quality
TV is
QV
QV Quality
QV is
Refr esh Device Var
RJC Temp
Sensor 1
Sensor 2
Backup 1-2
Backup 2-1
Average
Differen al 1-2
Differen al 2-1
Absolute Dif...
Low Select
High Select
Defa ul t Config
Config Wi zards
Input
Dual Input*
Analog Output
HART Sengs
Display
System Config
Advanc e
Sengs
Change Variable Mapping
PV is
Smart Range
SV is
TV is
QV is
Filter
PV Damp ing
Configure
Sensor
Ranging and
Mapping
Measure Mode
Input Type
EGU
BW Detecon
BW Holdoff me
Running Average
2Wire Offset
Sensor Informa on
Scaling
Custom Curve*
Scaling Enabled
DVx EGU
DVx Input Min.
DVx Input Max.
DVx Scale Min.
DVx Scale Max.
DVx CC En
DVx CC EGU
DVx CC ID
Backup 1-2
Backup 2-1
Av erage
Differen al 1-2
Differen al 2-1
Absolute Differenal
Low Select
High Select
DVx re ading
DVx EGU
Scaling
Custom Curve*
AO Zero
AO Full
AO URV
AO ORV
Fail Mode
Fail AO
Poll Addr
Num req preams
Num resp preams
Tag
Long Tag
Descriptor
Message
Date
Fina l asmbly num
Dev id
Hardware rev
Burs t Configuraon*
Dyn Var Di splay Flags
Decimal Places
Dev Var Display Flags
Configure Custom EGU*
Configure Custom Name*
PV is (DVX)
(DVX) LSL
(DVX) USL
(DVX) Min Sp an
(DVX) EGU
PV LRV
PV URV
Status
Input (PV) Capture
Variable Trim
AO Trim
AO Trim Reset
Loop Test
Input Simu laon
S1 Corrosion Det...
S2 Corrosion Det...
Unla tc h RA*
Tag
Long Tag
Descriptor
Mess ag e
Date
Dev id
Final asmbly num
Universal rev
Fld dev rev
Sowar e rev
Hardware rev
Poll addr
Num req prea ms
Num resp preams
Burst message 0,1,2*
Sx USL
Sx LSL
Sx Min Span
Sx s/n
RJC Temp
SEN1
SEN2
Backup 1-2
Backup 2-1
Average
Differen al 1-2
Differen al 2-1
Absolute Dif...
Low Select
High Select
2W
3W
4W
4000 ohms
...
Pt3850 100
Pt3850 200
…
1000 mV
...
J, K, E
…
If mV & T/C
If ohms &
RTD
Device Parameters
Device Informaon
Model
PV is
SV is
TV is
QV is
[PV Source DEV] LSL
[PV Source DEV] USL
[PV Source DEV] Min Span
PV LRV
PV URV
[PV Source DEV] EGU
Sensor 1 EGU
Sensor 2 EGU
Back up 1-2 EGU
Back up 2-1 EGU
Av er age EGU
Differenal 1-2 EGU
Differenal 2-1 EGU
Absolute Differenal EGU
Low Select EGU
High Select EGU
Sensor 1 Input Type
Sensor 1 s/n
Sensor 2 Input Type
Sensor 2 s/n
Filter
PV Damping
SEN1 Broken Wire De tecon
SEN1 BW Thresh old
SEN1 BW Holdoff me
SEN1 Running Average
SEN2 Broken Wire De tecon
SEN2 BW Thresh old
SEN2 BW Holdoff me
SEN2 Running Average
AO Zero
AO Full
AO URV
AO ORV
Fail Mode
AO Fail To Value
RA1 Enabled / Disabled*
RA2 Enabled / Disabled*
RA3 Enabled / Disabled*
RA4 Enabled / Disabled*
Sy stem Stat us
Addl Stat us Bytes
Subsystem Status
Input Status
User Cfg Status
Dev Variab le Status
Device Va ri able Trim
Device Va ri able Trim Reset
Display De vice Variable Trim
Sensor 1
Sensor 2
Input
Quality
Alarms
Range
Alarms*
Enabled
Sour ce
Response
Mode
Low
High
Latching
Burst Message 0
Burst Message 1
Burst Message 2
Mode
Cmd
Update Per
Max Update Per
Trig Mode
Trig Units
Trig Level
PCT
AO
PV
SV
TV
QV
Allow Meas Out of Comfor...
Allow Limited
Allow Dropping
Warning
Al arm (AO Fail)
Out of ra nge
In range
* These menu opons are only available when "Advanced Sengs" is enabled
.
Note: Any 2, 3, 4
or all can be
selected to display
in scrolling
Disable
Enable
Sx Corr Detecon
Sx Corr Res
Sx Corr Warn Leve l
Sx Corr Error Leve l
Sx Corr Base res
Capture Base Value
Basic Wi za rd
Dri Wiza rd
Configure
Input Types
RJC Temp
Sensor 1
Sensor 2
Disable
Enable
The Sensor Corrosion Sengs is available
only wh en in put ty pe is T/C, 3W/4W RTD
RJC Temp EGU
Sensor 1
Sensor 2
Disable
Enable
Range Alarm 1
Range Alarm 2
Range Alarm 3
Range Alarm 4
Unlatch RA