Moore Industries THZ3 - Page 72

www.miinet.com Moore Industries-International, Inc.
- 72 -
User’s Manual
238-741-00K
May 2019
Programmable Smart HART Temperature Transmitter
THZ
3
/ TDZ
3
SECTION 4
Figure 4.14. TDZ
3
or THZ
3
Status menu within the Custom Calibration Menu
Process
Variables
Setup
Custom
Calibraon
Review
Status
Input (PV) Capture
Variable Trim
AO Trim
AO Trim Reset
Loop Test
Input Simu laon
S1 Corrosion Det…
S2 Corrosion Det…
Unla tc h RA*
Sy stem Stat us
Addl St at us Bytes
Subsystem Status
Input Status
User Cfg Status
Dev Var Status
Sys Stat Summ ar y
In Errs and Warns
PV Status
SV St at us
TV Status
QV St at us
Ext dev status
Range Alarm Status
System Stat us Summary
Diagnosc Status
Input Error Summary
Input Warning
Summar y
Range Alarm Status
Ambient Temper atur e
Sensor Status 1
Sensor 1 St atus 1
Sensor 1 St atus 2
Sensor 1 Trim St atus
Sensor 2 St atus 1
Sensor 2 St atus 2
Sensor 2 Trim St atus
RJC Temp Config
Sensor1 Config
Sensor2 Config
BU 1-2 Config
BU 2-1 Config
Average Config
Diff 1-2 Config
Diff 2-1 Config
Abs Diff Config
LOSEL Config
HISEL Config
BAD DQ
S1 BAD
S2 BAD
S1 LIMITED
S2 LIMITED
On Backup
Backup Sensor BAD
Cfg: S1 Unit s Wrong
Cfg: S2 Unit s Wrong
Cfg: My Out Units BAD
Cfg: S1 Disabled
Cfg: S2 Disabled
Cfg: CC Inject ID
DV Cf g Er ror Summ
RJC Temp Status
Sensor1Status
Sensor2Status
Backup 1-2 Status
Backup 2-1 Status
Average St atus
Differenal 1-2 Status
Differenal 2-1 Status
Absolute Differenal
Low SelectStatus
High SelectStatus
Broken RJC
ADC Saturated
ADC Not Running
Bad Lead Res
Soware Sat
Bad Calib
Bad Config
Sensor Norm Fail
BW, Terminal 1
BW, Terminal 2
BW, Terminal 3
BW, Terminal 4
ADC Saturated
ADC Not Running
Bad Lead Res
Bad RJC Value
Soware Sat
Bad Calib
Bad Config
Sensor Norm Fail
Wrong Measurement
Wrong Sensor
Meas urem ent Misma..
Wrong Mo de
Lower Unit Mismatch
Upper Limit Mismatch
Lower Point Limits
Upper Point Limits
Lower Value Limits
Upper Value Limi ts
Upper Delta
Lower Delta
Span Value
Span Point
Trim Er ror
Same As S1
Same As S1
Same As S
See Figure 4.15
1
User Configuraon
Analog Out put St at us
Term Temp Sensor C….
Sensor 1 Config
Sensor 2 Config
Analog Output Config
Label Config
HART Co nfig
User Misc Config
Custom Curve 1 Config
Custom Curve 2 Config
Custom Curve 3 Config
Custom Curve 4 Config
Out put Fixed
Out put Saturated
Low Saturaon
High Saturaon
Low Calibraon Er ror
High Calibraon Error
Curren t Cali braon E…
Voltage Calibraon…
Out put Mode Config..
Fail Mode Config Error
URV/OR V Config Er ror
Zero /Full Config Er ror
Trim Er ror
Custom Calibration Menu
The Custom Calibration menu allows you to access the following menus: Status, Input
(PV) Capture, Variable Trim, AO Trim, AO Trim Reset, Loop Test, Input Simulation, S1
Corrosion Detection, S2 Corrosion Detection and Unlatch RA. Refer to Figure 4.14 below.
Status – Directs you to a sub-menu. When accessed, you will come to the following menu
options, System Status, Addl Status Bytes, Subsystem Status, Input Status, User Cfg
Status, and Dev Variable Status. Refer to Figure 4.14.