Why Motorola DS9208 Barcode Reader emits low/high beeps during programming?
If the Motorola Barcode Reader emits low/high beeps during programming, it indicates an input error or that the Cancel barcode was scanned. Scan the correct numeric barcodes within range for the parameter programmed.
Why Motorola Barcode Reader emits many beeps during programming?
If the Motorola Barcode Reader emits low/high/low/high beeps during programming, it means you've run out of ADF parameter storage space. Erase all rules and reprogram with shorter rules.
What does it mean if Motorola Barcode Reader emits low/high beeps during programming?
If the digital scanner emits low/high beeps during programming, it indicates an input error or that the Cancel barcode was scanned. Ensure you scan the correct numeric barcodes within the valid range for the parameter being programmed.
What does it mean if Motorola Barcode Reader emits low/high/low/high beeps during programming?
The digital scanner emitting low/high/low/high beeps during programming indicates that you've run out of ADF parameter storage space. Erase all existing rules and reprogram with shorter rules.
What to do if Motorola DS9208 decodes but does not transmit data?
If the Motorola Barcode Reader decodes the bar code but doesn't send the data to the host, ensure the reader is programmed for the correct host type by scanning the appropriate programming bar code. Also, check if the interface cable is loose and reconnect it. If the scanner emits 4 long low beeps, match the scanner's communication parameters to the host's settings. For 5 low beeps, configure the scanner's conversion parameters. If you hear low/high/low beeps, program the correct ADF rules. High/low beeps mean the scanner is buffering Code 39 data, which is normal if the Code 39 Buffering option is enabled.
Why aiming dot does not appear on my Motorola DS9208 Barcode Reader?
If the Motorola Barcode Reader's aiming dot doesn't appear when you press the trigger, there may be several reasons. First, ensure the digital scanner is receiving power by reconnecting the power supply if required. Check that you are using the correct host interface cable and that all cables are securely connected. The digital scanner might be disabled; enable it via the host interface or consult your technical support. For RS-232 Nixdorf B mode, ensure the CTS line is asserted. Finally, the aiming dot itself might be disabled, so enable it in settings.
How to fix Motorola DS9208 scanned data displayed incorrectly?
If the host displays scanned data incorrectly from the Motorola Barcode Reader, ensure the scanner is programmed to work with the host by scanning the appropriate host type programming bar code. For RS-232, match the scanner's communication parameters to the host's settings. If using a Keyboard Wedge, program the system for the correct keyboard type and turn off CAPS LOCK. Also, program the proper editing options like UPC-E to UPC-A Conversion.
What to do if Motorola Barcode Reader emits aiming dot but does not decode?
If the Motorola Barcode Reader emits the aiming dot but doesn't decode the barcode, first program the scanner to read that type of barcode. If the barcode is unreadable, scan test symbols to check for damage. Ensure the aiming dot is centered on the symbol. Also, disable Picklist mode if it's preventing decoding.
Why does Motorola Barcode Reader emit low beeps when not in use?
The Motorola Barcode Reader emitting low/low/low/extra low beeps when not in use usually indicates an RS-232 receive error. This is normal during a host reset. Otherwise, set the scanner's RS-232 parity to match the host setting.
Why Motorola Barcode Reader aiming dot does not appear when pressing the trigger?
The aiming dot might not appear due to several reasons: * The digital scanner might not be receiving power. If your setup requires a power supply, ensure it's properly connected. * The host interface cable could be incorrect. Verify you are using the correct cable. * Cables might be loose. Check and re-connect all cables. * The digital scanner could be disabled. Enable it via the host interface, especially for IBM 468x and USB IBM hand-held, IBM table top, and OPOS modes. If not, consult with your technical support. * If using RS-232 Nixdorf B mode, the CTS might not be asserted. Assert the CTS line. * The aiming dot itself might be disabled. Enable the aiming dot.
General| Drop Specification | Withstands multiple 5 ft./1.5 m drops to concrete |
|---|---|
| Scanning Technology | Imager |
| Tilt Angle | ± 65° |
| Skew Angle | ± 60° |
| Connectivity | USB, RS232, Keyboard Wedge |
| Decode Capability | 1D, 2D and PDF417 |
| Light Source | 650nm visible laser diode |
| Operating Temperature | 32° to 104° F/0° to 40° C |
| Print Contrast | 25% minimum reflectance |
| Pitch Angle | 60° |
| Storage Temperature | -40° to 158° F (-40° to 70° C) |
| Humidity | 5% to 95% relative humidity, non-condensing |
| Electrical Safety | UL |
| EMC | FCC Part 15 Class B |
| Cable Length | 6 ft (1.8m) |
| Power Consumption | 2.5 Watts (500mA @ 5V) |
| Scan Pattern | Omnidirectional |
To Next Page
