To Next PageTo Next PageWhy MTD Lawn Mower wheels will not propel?
If the wheels of your MTD Lawn Mower won't propel, it could be because the belt isn't installed properly (check the belt for proper pulley installation and movement) or debris is clogging the drive operation (clean out the debris).
Why does my MTD 500 engine run erratically?
An MTD Snow Blower engine might run erratically due to several reasons: 1. Check if the engine is running on CHOKE; if so, move the choke control to the OFF position. 2. Stale fuel can cause issues; replace it with clean, fresh gasoline. 3. Water or dirt in the fuel system can also be a culprit; drain the fuel tank and refill with fresh fuel. 4. If the above steps don't resolve the issue, the carburetor might be out of adjustment. In this case, contact a Tecumseh Engine Service Center.
Why MTD 500 has loss of power?
Loss of power in your MTD Snow Blower could be due to: * A loose spark plug wire. Connect and tighten the spark plug wire. * A plugged gas cap vent hole. Remove any ice and snow from the gas cap, ensuring the vent hole is clear.
Why MTD Snow Blower engine running erratically?
An MTD Snow Blower engine running erratically could be due to: * The engine running on CHOKE. Move the choke lever to the RUN position. * Stale fuel. Replace with clean, fresh gasoline. * Water or dirt in the fuel system. Drain the fuel tank and refill with fresh fuel.
Why overhead chute crank does not stay stationary while throwing snow using an overhead chute control in MTD Snow Blower?
If the overhead chute crank on your MTD Snow Blower does not stay stationary, there might be insufficient preload applied to the chute control. Refer to the Service section to adjust the chute preload.
Why MTD Lawn Mower engine fails to start?
The MTD Lawn Mower engine might fail to start due to several reasons. It could be that the blade control handle is disengaged (engage it), the spark plug wire is disconnected (connect it), the fuel tank is empty or contains stale fuel (fill it with clean, fresh gasoline), the engine isn't primed (refer to the engine manual), the spark plug is faulty (clean, adjust the gap, or replace it), the fuel line is blocked (clean it), or the engine is flooded (wait a few minutes to restart, without priming).
What to do if MTD 500 engine fails to start?
If your MTD Snow Blower engine won't start, here's what you can check: 1. Ensure the choke control is in the ON position. 2. Make sure the spark plug wire is securely connected. 3. Verify the fuel tank isn't empty and contains fresh gasoline. 4. Prime the engine as detailed in the Operation section of your manual. 5. Inspect the spark plug; clean, adjust the gap, or replace it if necessary. 6. Confirm the safety key is fully inserted into the switch.
How to fix MTD Snow Blower engine that fails to start?
If your MTD Snow Blower engine won't start, several factors could be at play. First, ensure the choke is in the CHOKE position and the spark plug wire is securely connected. Next, check that the fuel tank isn't empty or filled with stale fuel; if so, replenish it with clean, fresh fuel. Make sure you've primed the engine as per the Engine Manual. Inspect the spark plug for faults, cleaning, adjusting the gap, or replacing it if necessary. Verify the safety key is fully inserted into the switch. Lastly, if your model has an electric start, confirm the extension cord is properly connected to both the snow blower and a grounded 120V AC outlet.
General| Type | Two-Stage |
|---|---|
| Engine Type | 4-Cycle |
| Auger Material | Steel |
| Stages | Two-Stage |
| Engine Displacement (cc) | 179 cc |
| Max Throw Distance (ft) | 40 ft |
| Number of Forward Speeds | 6 |
| Number of Reverse Speeds | 2 |
| Chute Control | Manual |
General instructions for safe operation of the machine.
Precautions for handling gasoline safely to prevent fire and injury.
Steps to prepare the area and yourself before operating.
Instructions for operating the snow thrower safely.
Guidelines for maintaining the machine and storing it properly.
Procedures to safely clear snow or ice from the chute.
Procedure to test and verify proper operation of the auger control.
Operation of augers and related controls.
Operation of drive control lever and steering triggers.
How to engage the augers to start throwing snow.
Adjusting drive control cable for both hydro and non-hydro models.
Problems related to engine starting, running, and overheating.
Troubleshooting unit propulsion, snow discharge, and chute rotation.
