MTX 1330-X02 - Page 180

701333-004 Index-3
Index
419 – DID Load Adjust, 5-20
421 – Operator Panel Adjust, 5-21
422 – Start Mode After Eject, 5-21
423 – Report Intervention, 5-21
501 – Printer Emulation Mode, 5-22
502 – Buffer Size, 5-22
503 – DC1/DC3 Recognition, 5-22
504 – Baud Rate, 5-23
505 – Parity, 5-23
506 – Data Bits, 5-24
507 – Stop Bits, 5-24
508 – Modem Control, 5-24
509 – Handshaking, 5-25
510 – Reserved, 5-25
511 – RS-422 Polarity, 5-25
601 – Interface, 5-26
602 – Idle Timeout, 5-26
603 – Interface Type, 5-27
701 – Print Configuration, 5-27
702 – Quick Reference, 5-30
703 – Set Factory Defaults, 5-30
704 – POR Custom Set, 5-30
705 – Save Custom Set, 5-31
706 – Recall Custom Set, 5-31
707 – Display Character Count, 5-31
ASCII Configuration options
Alarm on Error, 5-15
Auto Eject, 5-17
Auto Return, 5-17
Automatic Perforation Skip, 5-12
Bar Code Control, 5-13
Baud Rate, 5-23
BC Space CHR, 5-13
Bit Graphics, 5-12
Bold Print Enable, 5-9
Buffer Size, 5-22
Carriage Return Definition, 5-11
Characters per Inch, 5-5
Data Bits, 5-24
DC1/DC3 Recognition, 5-22
Define Horizontal Tab (810), 5-11
DID Load Adjust, 5-20
Display Character Count, 5-31
Display Language, 5-8
DOD Load Adjust, 5-20
Form Length, 5-7
Handshaking, 5-25
Horizontal Offset, 5-18
Horizontal Registration, 5-19
Idle Timeout, 5-26
Ignore Sign, 5-12
Interface, 5-26
Interface Type, 5-27
Key Alarm, 5-14
Language, 5-7
Left Margin, 5-5
Line Feed Definition, 5-11
Line Spacing, 5-7
Lines per Inch, 5-6
Maximum Print Position, 5-6
Modem Control, 5-24
Module Type Override, 5-17
Mono/Dual Case, 5-9
Operator Panel Adjust, 5-21
Paper Eject Adjustment, 5-18
Paper Jam Sensor Enable, 5-19
Paper Out Sensor Enable, 5-19
Paper Skew Sensor Enable, 5-20
Parity, 5-23
POR Custom Set, 5-30
Print Configuration, 5-27
Print Head Column Spacing, 5-15
Print Head Style, 5-15
Print Quality, 5-10
Printer Emulation Mode, 5-22
Recall Custom Set, 5-31
Report Intervention, 5-21
Reserved, 5-25
Ribbon Track Select Adjustment, 5-16
Ribbon Type Override, 5-16
RS-422 Polarity, 5-25
Save Custom Set, 5-31
Save Operator Format, 5-14
Set Factory Defaults, 5-30
Start Mode After Eject, 5-21
Stop Bits, 5-24
Two-Pass Print Direction, 5-9
Vertical Tab Setting, 5-10
Attribute Selectable Highlighting option (3270), 4-16
Auto Eject option (3270), 4-21
Auto Eject option (ASCII), 5-17
Auto Return option (ASCII), 5-17
Automatic Perforation Skip option (ASCII), 5-12
B
Bar Code Control option (ASCII), 5-13
Base Color option (3270), 4-16
Baud Rate option (ASCII), 5-23
BC Space CHR option (ASCII), 5-13
Bit Graphics option (ASCII), 5-12
Bold Print Enable option (3270), 4-10
Bold Print Enable option (ASCII), 5-9
Buffer Reprint option (3270), 4-33
Buffer Size option (3270), 4-26
Buffer Size option (ASCII), 5-22