Nabco GT20 User Manual (English)

Other manuals for Nabco GT20

Owner's Manual10 pages

Wire And Programming Manual43 pages

Questions and Answers:

C
Christine DavisAug 13, 2025
How to fix Nabco Door Opening System when the drive unit fails to react?
- D
  Dr. Taylor Sparks DVMAug 13, 2025
  If the Nabco Door Opening System drive unit isn't reacting, with no automatic opening or activation from sensors or buttons, the issue might be a missing power supply voltage. First, switch on the main installation switch in the side cover. Then, measure the mains supply voltage and check its cabling, fixing any problems found. If these steps don't work, the control unit may need to be replaced.
J
Julie MartinAug 17, 2025
What to do if Nabco GT20 drive unit fails to open?
- A
  Ann TurnerAug 17, 2025
  If your Nabco Door Opening System drive unit isn't opening, it could be due to active or incorrectly cabled safety sensors. Try removing any obstacles that might be triggering the sensors. Also, check the cabling between the safety sensor and the control unit, correcting any issues. If problems persist, consider replacing the safety sensor.
N
Nancy KentAug 21, 2025
Why Nabco GT20 Door Opening System drive unit fails to close?
- D
  Douglas DukeAug 21, 2025
  If your Nabco Door Opening System drive unit isn't closing, it might be because one or more safety sensors are active or the cabling is incorrect. First, make sure to remove any obstructions that could be activating the safety sensors. Next, check the cabling between the safety sensor and the control unit, and fix any detected issues. If the problem continues, you may need to replace the safety sensor.
J
jessicatuckerAug 25, 2025
How to fix Nabco GT20 Door Opening System when the operating mode cannot be changed?
- J
  Jacqueline Norris MDAug 25, 2025
  If you're unable to change the operating mode on your Nabco Door Opening System, the ribbon cable might not be correctly plugged in, or not plugged in at all. Check the ribbon cable and correct any issues.
H
Hunter GutierrezAug 28, 2025
What to do if Nabco Door Opening System drive unit fails to close?
- E
  elizabeth03Aug 28, 2025
  If the Nabco Door Opening System drive unit fails to close, the issue might be related to the safety sensors. Check if any safety sensors are active or if their cabling is faulty. Start by removing any obstructions that might be triggering the sensors. Next, examine the cabling between the safety sensor and the control unit, correcting any detected issues. If the problem continues, replace the safety sensor.
W
Wendy ButlerSep 1, 2025
How to fix Nabco GT20 drive unit that fails to react?
- Q
  qdonovanSep 1, 2025
  If the Nabco Door Opening System drive unit isn't reacting, with no automatic opening or response from sensors or buttons, the problem could be a missing power supply voltage. Go to the side cover and turn the main installation ON. Measure the main supply voltage and check the cabling, fixing any deficiencies found. If these steps don't work, the control unit may need replacement.
C
Christine HillSep 5, 2025
Why the Operating Mode of Nabco GT20 cannot be changed?
- N
  newtonrussellSep 5, 2025
  If you cannot change the operating mode on your Nabco Door Opening System, the ribbon cable might not be correctly plugged in, or not plugged in at all. Check the ribbon cable and eliminate any problems.
J
joyhubbardSep 8, 2025
What to do if Nabco GT20 Door Opening System door panel encounters resistance during manual opening?
- P
  Penny FisherSep 8, 2025
  If, prior to commissioning, the Nabco Door Opening System's door panel meets resistance during manual opening and closes at high speed, the motor connector plug may not be correctly connected. Ensure you plug the motor connector plug into the correct socket in accordance with application (pulling/pushing function).