NAD C 546BEE User Manual

CD-R AND CD-RW AUDIO DISCS
The C 546BEE can play back CD-R or CD-RW audio discs that have been
recorded on a computer or CD recorder. The quality of CD-R or CD-RW
audio discs varies widely which may aect playability. Some factors that
aect playability:
• The quality of the disc itself. Generally speaking, CD-R or CD-RW blanks from
well-renowned companies give better results than unbranded ones.
• The quality of CD-recorder or computer CD re/writer. Some recorders
and writers produce better results than others.
• The CD-R and CD-RW were created with high-speed writing. In general,
the quality of a CD-R or CD-RW is better when produced at a lower
speed against a higher speed on the same recorder or re/writer.
PLAYING MP3/WMA FILES
The C 546BEE can play MP3/WMA formatted recordings on CD-R or CD-RW
discs. You may mix any of the le types on the disc. Using the CD 9 remote
control, one can select through the MP3/WMA folders and les as well as
start playback through the following steps
1 Load the applicable disc.
2 Press [FOLDER D/F ] to select desired folder. Press [ENTER].
3 Press [FILE A/S ] to select desired le number. Press [ENTER] to start playback.
NOTES
• Thelenumberisrecognizedperdisc,notperfolder–thatis,the
number assigned to each le corresponds to their sequence in the disc.
• Ifyouwanttoselectlenumber“119”inadiscwherethereare100or
moreMP3/WMAles,press“1”twiceandthen“9.”
• Duringdiscplayback,itispossibletoselectthroughthefolderorlelists
(using [FOLDER D/F ] or [FILE A/S ] buttons) without interrupting the
current le being played back.
IMPORTANT NOTICE
Customers should note that permission is required in order to download
MP3/WMA les and music from the Internet. NAD ELECTRONICS
INTERNATIONAL has no right to grant such permission. Permission
should always be sought from the copyright owner.
PROGRAMMING
The program function enables you to store your favorite tracks from any
disc in the player memory. When programming a sequence of tracks, the
C 546BEE must be in STOP mode. Using the CD 9 remote control, enter your
desired program sequence through the following steps
1 Press [PROG] button of CD 9 remote control. The display indicates “P00
T000”. The “000” in the “T000” keeps on blinking, meaning the player is
awaiting the rst Program entry.
2 Use the Direct-Entry numeric keypad buttons to enter the rst track in
your planned sequence. For example, press “5” to enter track number
5. Upon entering the track number, the VFD will show “P01 T005” with
“005” of “T005” blinking 3 times.
3 The display will revert to show “P02 T000”, indicating that the player is
ready for your second program entry. For example, press “8” to enter
track number 8. Upon entering the second track, the VFD will show “P02
T008” with “008” of “T008” blinking 3 times.
4 Repeat steps 2 and 3 to select and store other track numbers in
memory, up to a maximum of 40 entries. When you reach P40, the three
blinking digits will keep on ashing and won’t stop. This is unlike the
previous 39 entries wherein after an entry blinked thrice, it moves on to
the next program number/entry.
5 Press [PROG] to end or nalize the program – the VFD will show the last
programmed number and track.
6 Press [u] to start playback of the rst programmed track. Rotate [PLAY/
PAUSE/SKIP] if you wish to SKIP forward/backward the programmed tracks.
NOTES
· Ifyouwanttoselectlenumber“119”inadiscwherethereare100or
moreMP3/WMAles,press“1”twiceandthen“9.”
· Pressing [g] key at any time during the programming procedure will put
to a STOP to the sequence and clear all the currently programmed tracks
orles.VFDwillrevertbacktodisplayingthetotalnumberoftracks
and total playback time for audio CD and total number of les for MP3/
WMA.
· Pressing [g]keytwiceduringprogramplaybackwillresulttohavingthe
whole program list deleted.
REVIEW/EDIT PROGRAM LIST
1 Initiate review of your programmed entries by pressing [PROG].
· If you are still in programming mode, press [PROG].
· If during program playback, press [g] once, then [PROG].
2 The VFD will show the rst Program Number and the corresponding
“blinking” programmed track.
3 To change the programmed track of a particular sequence, use the
Direct-Entry numeric keypad buttons. Press [9/0] to move forward
or backward the programmed tracks as well as review the list and
change if so desired.
4 If you want to delete a particular program sequence during program
review, press [CLEAR] key.
Example: Delete “P34 T067” from a total of 40 program entries
(display) “P34 T067” $ [CLEAR] $ (display) “P34 T000” (“000” blinking)
$ enter desired track/song number to replace T067 or press [PROG] to
nalize deletion process
If [PROG] is pressed without entering a new track/song number, the
total 40 program entries will be reduced to 39 entries. The program
sequence will adjust accordingly starting from the deleted program
number.
5 After nalizing your program changes or completing your review, press
[PROG] again.
PROGRAM PLAYBACK
1 To play the stored program, press [u] while you are in “PROGRAM”
mode. “PROG” icon will appear in the display, indicating that a stored
program is being played. During Program Play, the SKIP buttons will
access only the tracks in the program list.
2 If you want to play only a portion of a stored program, initiate play and
press SKIP to jump over the programmed tracks that you don’t want to
hear.
STOP OR DELETE PROGRAM
1 To terminate Program play, press [g] once. The stored track list remains
in memory. If you want to play the program again, simply press [u].
2 To clear the program memory, perform any of the following steps
· Press [g] twice during program playback.
· Press [k] to open the disc tray.
· Switch OFF the C 546BEE by pressing the Standby button.
· Switch to another source other than CD mode by pressing front
panel’s [SOURCE] button or [USB] source button in CD 9.
OPERATION
USING THE C 546BEE  CD MODE
11
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

NAD C 546BEE Specifications

General

Frequency range	5 - 20000 Hz
Audio formats supported	MP3, WMA
Signal-to-Noise Ratio (SNR)	118 dB
Total Harmonic Distortion (THD)	0.0035 %
CD-R playback	Yes
Device type	Portable CD player
Product color	Graphite
Channel separation	110 dB
Playback disc types	CD-R, CD-RW
Disc types supported	CD-R
Power	9 W
Power source type	AC
AC adapter input voltage	230 V
Power consumption (standby)	0.5 W
USB 2.0 ports quantity	1
Package weight	6300 g

Weight and Dimensions

Depth	435 mm
Width	307 mm
Height	89 mm
Weight	4900 g