NAIM UnitiLite - The Rooms Menu; The Speakers Menu

18
4.3.10 Front Panel Input
Parameter Options
Enabled: Yes / No
Name: User denable
Input Trim: ±10dB
Format: Auto / Analogue / Digital. If Auto is
selected the front panel input will
automatically detect the audio signal
format (analogue or digital) and
congure the input appropriately.
Specifying Analogue or Digital will x
the front panel input format.
4.3.11 Other Inputs
Parameter Options
Enabled: Yes / No
Name: User denable
Input Trim: ±10dB
AV Fixed Volume: Yes / No
If No is selected the input will behave
normally. If Yes is selected the input
will operate at a xed volume and
volume control will be disabled. Fixed
volume enables Uniti Series products
to be used in multi-channel AV systems
with volume control handled by the AV
processor. Take care when selecting AV
Fixed Volume.
Note: AV xed volume is available on rear panel analogue
inputs only.
4.4 The Rooms Menu
The Rooms setup menu enables
Uniti Series products to broadcast
audio from their UPnP™, iRadio, or
USB inputs simultaneously to up to
four other Naim streamer products
connected to the same home network.
Note: The Rooms menu is only visible when the multiroom
input is enabled. See Section 4.3.5.
4.5 The Speakers Menu
The Speakers setup menu enables a variety of speaker
parameters to be adjusted. The options are tabulated and
described in the following sections:
UnitiQute 2
Parameter Options
Type: Large / Small /
None
Loundess: Yes / No
Max. Volume: 0 to 100 (adjust
using handset 6 or 5 keys)
Balance: -10 to + 10 (adjust using handset 6 or
5 keys)
Select Large when large (full bandwidth) speakers are
connected to the UnitiQute 2 speaker outputs or when
its preamplier output is connected to an external power
amplier or to a subwoofer used to augment the speakers’
low frequency performance.
Select Small when satellite (restricted bandwidth) speakers
are connected to the UnitiQute 2 speaker outputs and
the preamplier output is connected to a subwoofer
providing the low frequency element of the speaker system.
When Small is selected a high-pass lter is applied to the
UnitiQute 2 speaker outputs.
Select None when no speakers are connected to the
UnitiQute 2 speaker outputs.
Note: The UnitiQute 2 preamplier output is enabled
regardless of the type of speakers selected.
The UnitiQute 2 includes a Loudness parameter in its
Speakers menu. Engaging the Loudness option applies
low frequency boost to the speaker and preamplier
outputs that decreases as the volume setting is increased.
Through compensating for the ear’s reduced low frequency
sensitivity at low volume levels, the Loudness function can
make low volume listening more satisfying.
Note: The loudness contour operates at volume settings
between 0 and 55.
The speaker Max. Volume and Balance parameters specify
maximum allowed volume, and the channel balance
respectively.
NaimUniti 2
Parameter Options
Type: Large+Sub
/ Large /
Small+Sub /
None
Max. Volume: 0 to 100 (adjust using handset 6 or 5
keys)
Balance: -10 to + 10 (adjust using handset 6 or 5
keys)
4. Configuration
Front 4/4
Enabled: Yes
Name: Front
Input Trim: 0
4Format: Auto
Analogue 1 1/4
4Enabled: Yes
Name: Analogue 1
Input Trim: 0
AV Fixed Volume No
Speakers 1/3
4Type: Large+Sub
Max. Volume: 100
Balance: 0
Speakers 1/3
4Type: Large
Loudness No
Max. Volume: 100
Balance: 0
Rooms 1/2
4aQute-3F65
Uniti-2E23