NAPCO Security Group
NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 1
Page 34 Programming Instructions, Volume 1
Example: Program a code of "2222" for user 02, with User Option of " User Program" , User " Level 3" and Output Control
Option "Keypad No. 1". Enter "2222" for a user code, "2 3" for user option and "blank(•) 1" for output control option.
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described
above and press
U to save. Similarly, to cancel a code, blank out each number of the code and press U to save.
USER AUTHORITY LEVEL
KEYPAD DISPLAY FUNCTION MENU
FUNCTION LEVEL*
DISPLAY ZN FAULTS 1
DISPLAY ZN BYPASSED 1
DISPLAY ZN DIRECTORY 1
ACTIVATE BELL TEST 1
DISPLAY PHONE #’S 1
DISPLAY SYS TRBL 1
DISPLAY FIRE ALARM 1
DISPLAY FIRE TRBL 1
DISPLAY OP/CL 3
ACTIVATE OVERVIEW 3**
ACTIVATE CHIME 1
ACTIVATE WATCH 2
RESET SYSTEM TRBL 3
RESET SENSOR MSG 3
START EXIT TIME 1
FAULT FIND ***
ACTIVATE DIALER TEST 3
DISPLAY ALARM LOG 3
DISPLAY TOTAL LOG 3
DISPLAY FIRE LOG 3
DISPLAY OP/CL LOG 3
DISPLAY SYSTEM LOG 3
AUTOARM IN 1-4HRS 2
DISPLAY AUTOARM SCHD 3
ACTIVATE PROGRAM 3**
ACTIVATE DOWNLOAD 3
DISPLY RF XMITTER STAT 1
RELAY CONTROL 1
NOTES:
* Minimum Level required to access function.
** Level-3 Code with appropriate user option.
*** Requires Dealer Keypad Program Code.
BURGLARY USER OPTIONS
OPTIONS
EXPLANATION
Disabled User Code not active in this area.
Blocked View
Allows User Code to block another code from being viewed by another user.
An unblocked code cannot view a blocked code, but a blocked code can view
all codes. The master user code and the dealer program code can view all
codes.
User Program
User Program Option is enabled for Keypad 1 only, wherever it is connected
(any area). If enabled, Level 3 must also be enabled.
Bypass Allows User Code to bypass zones.
Overview
This option, along with Level 3 Authorization, enables selection of OVERVIEW
mode at a keypad. This Mode provides a system status display of all areas at a
glance.
Arm Only Prevents User Code from disarming this area.
Service
A Service Code has restricted arm/disarm rights; if an area is armed with a
Service Code, a “S” appears on the GEMC-FK1 keypad and the area can be
disarmed with any valid User Code, including a Service Code. If the area is
armed with OTHER than a Service Code, it CANNOT be disarmed with a
Service Code. This is typically used to allow tradesmen access to premises
under control of the owner.
Ambush
There are two types of Ambush Codes: (1) A 2-digit code (prefix) that is entered
immediately prior to (and as part of) the regular User Code and (2) A separate and
unique User Code. Disarming with an Ambush Code will cause a silent report to be
sent to a central station. Thus, should a user be forced to disarm, he can silently
signal an emergency while appearing to be merely disarming the system.
Output
This is normally used to activate an output while an area is disarmed. A code
with the Output option will not function as an arm/disarm code. When the code
is entered, the keypad will display “ENTER NOW” and the brown wire on the
keypad will become Active Low (ground potential) for 7 seconds.
Related User Options: “ Ambush Code” (Address 0990), “ Panel Output Control
Code” (Address 0985), “Dealer Security Code” (Address 0995) & “Enable User Code by
Area” (Address 5380-5574).
Enter User Codes (cont'd)
To Next Page
Loading...
Need help?
General
