To Next PageTo Next PageWhat to do if Napoleon BIPRO665RBNSS3 won't light with igniter?
If the main burner of your Napoleon Grill won't light with the igniter but lights with a match, the jet-fire outlet is likely dirty or clogged. Clean the jet-fire outlet using a soft bristle brush.
What to do if burners will not cross light on my Napoleon BIPRO665RBNSS3?
If the burners on your Napoleon Grill will not cross light each other, it is likely due to dirty or corroded cross light brackets. Clean or replace the brackets as required.
Why is the burner output on my Napoleon BIPRO665RBNSS3 too low?
If the Napoleon Grill's burner output is too low on the 'high' setting, accompanied by a rumbling noise and blue flame, it could be due to several reasons. First, check the gas level in the propane cylinder. Then, inspect the supply hose to ensure it is not pinched and reposition it if necessary. Clean the burner orifice and venturi tube to remove any obstructions like spider webs. For propane, ensure the lighting procedure is followed carefully: all gas grill valves must be off when the tank valve is turned on, and the tank should be turned on slowly to allow pressure to equalize.
What to do if my Napoleon BIPRO665RBNSS3 Grill has excessive flare-ups?
To address excessive flare-ups or uneven heat on your Napoleon Grill, first, ensure the sear plates are correctly installed with the holes facing the front and the slots at the bottom. Preheat the grill with both main burners on high for 10 to 15 minutes. Regularly clean the sear plates and drip pan to remove grease and ash buildup. Do not line the drip pan with aluminum foil.
Why are the lights not working on my Napoleon BIPRO665RBNSS3?
If your Napoleon Grill's oven and control panel lights aren't working, start by ensuring the unit is properly connected to a working GFI protected outlet and that the transformer cord is plugged into the power box. Replace the fuse located on the outlet line of the transformer. Check the transformer output; it should be 12VAC, and replace it if required. Clean any corroded or loose terminals on the switch or circuit board, ensuring connectors are firmly pushed together. Access the circuit board under the electrical cover on the left side of the cabinet. If only the oven lights are out, replace the bulbs as per the maintenance section instructions.
Why is the electronic ignition not working on my Napoleon BIPRO665RBNSS3 Grill?
If the electronic ignition on your Napoleon Grill is not working, first, ensure the unit is connected to a working GFI protected outlet and the transformer cord is plugged into the power box. Then, check and replace the fuse located on the outlet line of the transformer. Verify the transformer output (should be 12VAC) and replace if necessary. Clean any corroded or loose terminals on the switch or circuit board, ensuring they are firmly connected. Access to the circuit board is under the electrical cover on the left side of the cabinet. Replace the igniter, which is located under the electrical cover. Clean or replace dirty or corroded electrodes as needed.
How to fix low heat on my Napoleon BIPRO665RBNSS3 Grill?
If you experience low heat or low flame on your Napoleon Grill when the valve is turned to high, there are several possible causes. For propane, ensure the lighting procedure is carefully followed, with all gas grill valves in the off position when the tank valve is turned on, and turn the tank on slowly to allow pressure to equalize. For natural gas, the supply line might be undersized, requiring a pipe sized according to the installation code. For both gas types, improper preheating could be the issue; preheat the grill with both main burners on high for 10 to 15 minutes.
Why is 'paint' peeling inside my Napoleon BIPRO665RBNSS3 Grill lid?
If you see what appears to be “paint” peeling inside the lid or hood of your Napoleon Grill, this is not a defect. The finish on the lid and hood is porcelain and will not peel. The peeling is caused by hardened grease, which dries into paint-like shards that flake off. Regular cleaning will prevent this.
Why do my Napoleon BIPRO665RBNSS3 burners have a yellow flame?
If the burners on your Napoleon Grill burn with a yellow flame and a smell of gas, it may be due to a spider web or other debris, or improper air shutter adjustment. Thoroughly clean the burner by removing it. Open the air shutter slightly according to combustion air adjustment instructions; this adjustment must be done by a qualified gas installer.
Why are flames lifting away from the burner on my Napoleon Grill?
If the flames lift away from the burner on your Napoleon Grill, accompanied by a smell of gas, and possibly difficulties in lighting, it is likely due to improper air shutter adjustment. Close the air shutter slightly according to combustion air adjustment instructions. Note that this adjustment must be done by a qualified gas installer.
General| Model | BIPRO665RBNSS3 |
|---|---|
| Category | Grill |
| Type | Built-in |
| Cooking Area | 665 sq. in. |
| Burners | 4 |
| Rotisserie Burner | Yes |
| Infrared Searing Burner | Yes |
| Material | Stainless Steel |
| Ignition | Electronic |
| Construction | Stainless Steel |
| Fuel Type | Natural Gas/Propane |
| Primary Burner | 15, 000 BTU |
| Secondary Burner | 15, 000 BTU |
| Warranty | Limited Lifetime |
Details warranty terms, exclusions, and definitions of use.
Requirements for propane cylinders and connection safety.
Procedures for connecting the gas supply to the grill.
Important safety considerations for electrical components and connections.
First-time use, initial odor, and wind effects on performance.
Techniques for searing and cooking with main burners.
Method for searing or foods requiring short cooking times.
Method for slow and even cooking of larger cuts of meat.
Instructions for using the rear burner, especially with rotisserie.
Guide for using the smoker burner and smoker tray with wood chips.
Adjusting air shutters for optimal burner flame and performance.
Details on required information for parts and warranty claims.
List of necessary tools for assembling the grill.
Instructions for turning on the main power switch.
How to adjust light intensity and perform a factory reset.
Operation of the motion sensor for automatic lighting.
How to select and customize light colors.
Information on automatic shut-off timers for lights.
