Napoleon BIPRO 665 - User Manual

Other manuals for Napoleon BIPRO 665

Instructions60 pages

User Manual64 pages

Questions and Answers

D
David FoxAug 17, 2025
What to do if my Napoleon Grill has excessive flare-ups or uneven heat?
- M
  Monica RussellAug 17, 2025
  To resolve excessive flare-ups or uneven heat in your Napoleon Grill: * Make sure the sear plates are correctly installed with the holes facing the front and the slots on the bottom. Refer to the assembly instructions. * Preheat the grill with both main burners on high for 10 to 15 minutes. * Regularly clean the sear plates and drip pan. Do not line the pan with aluminum foil; instead, refer to the cleaning instructions.
S
Shawn GardnerAug 20, 2025
Why is the burner output on my Napoleon BIPRO 665 too low?
- C
  carpenterscottAug 20, 2025
  If the burner output on the high setting of your Napoleon Grill is too low, producing a rumbling noise and fluttering blue flame, consider these potential causes and solutions: 1. Check the gas level in the propane cylinder. 2. Reposition the supply hose if it is pinched. 3. Clean the burner orifice and venturi tube to remove any blockages like spider webs. 4. Follow the correct lighting procedure, ensuring all gas grill valves are off when the tank valve is turned on, and turn the tank on slowly to allow pressure to equalize. Refer to the lighting instructions. The propane regulator might be in a 'low flow' state.
B
Bailey BennettAug 22, 2025
What to do if my Napoleon BIPRO 665 main burner won't light with the igniter?
- J
  Jonathan WrightAug 23, 2025
  If the main burner on your Napoleon Grill won't light with the igniter but lights with a match, the jet-fire outlet is likely dirty or clogged. Clean the jet-fire outlet using a soft bristle brush.
K
Kyle LewisAug 26, 2025
Why is the electronic ignition not working on my Napoleon BIPRO 665 Grill?
- H
  hpierceAug 26, 2025
  If the electronic ignition on your Napoleon Grill is not working, check the following: * Ensure the unit is properly connected to a working GFI protected outlet. * Check and replace the fuse located on the outlet line of the transformer. * Verify the transformer output (should be 12VAC) and replace if required. * Clean any corroded or loose terminals on the switch or circuit board, ensuring connectors are firmly pushed together. The circuit board is accessible under the electrical cover on the left side of the cabinet. * Replace the igniter, which is located under the electrical cover. * Clean or replace dirty or corroded electrodes as needed.
Z
zwaltersAug 28, 2025
Why is 'paint' peeling inside my Napoleon Grill lid?
- J
  Justin ChristensenAug 28, 2025
  If you notice peeling that looks like paint inside the lid or hood of your Napoleon Grill, don't worry, it's not a defect. The finish is porcelain and won't peel. This occurs when grease builds up on the inside surfaces, hardens, and then flakes off. Regular cleaning, as described in the cleaning instructions, will prevent this.
L
Lauren NelsonAug 30, 2025
How to fix low heat or low flame on my Napoleon Grill?
- N
  Nicholas LewisAug 30, 2025
  To address low heat or low flame issues with your Napoleon Grill, check the following: * For propane, carefully follow the lighting procedure, ensuring all gas grill valves are off when you turn on the tank valve. Turn the tank on slowly to allow pressure to equalize. Refer to the lighting instructions. * For natural gas, ensure the pipe is sized according to the installation code. * For both gases, preheat the grill with both main burners on high for 10 to 15 minutes.
K
katherine34Sep 2, 2025
Why are the oven and control panel lights not working on my Napoleon BIPRO 665?
- M
  Mrs. Margaret HernandezSep 3, 2025
  If your Napoleon Grill's oven and control panel lights aren't working, check the following: * Ensure the unit is connected to a working GFI protected outlet. * Check and replace the fuse located on the outlet line of the transformer. * Verify the transformer output (should be 12VAC) and replace if necessary. * Clean any corroded or loose terminals on the switch or circuit board, ensuring connectors are firmly pushed together. The circuit board is accessible under the electrical cover on the left side of the cabinet. * If only the oven lights are out, replace the bulbs as per the instructions in the maintenance section of the manual.
A
Anthony LopezSep 5, 2025
Why do my Napoleon BIPRO 665 burners have a yellow flame and smell of gas?
- M
  michellejohnsonSep 5, 2025
  If your Napoleon Grill burners are producing a yellow flame accompanied by the smell of gas, it may be due to a spider web, other debris, or an improper air shutter adjustment. Thoroughly clean the burner after removing it, following the general maintenance instructions. A qualified gas installer should slightly open the air shutter according to the combustion air adjustment instructions.
J
John FowlerSep 8, 2025
What to do if the infrared burner on my Napoleon BIPRO 665 Grill flashes back?
- S
  Shane LewisSep 8, 2025
  If the infrared burner on your Napoleon Grill flashes back, making a loud 'whoosh' sound, followed by a blow-torch sound and dimming, it could be due to several reasons: * Ceramic tiles overloaded with grease. * Clogged ports. * Overheating due to inadequate ventilation. * Cracked ceramic tile. * Leaking gasket. * Weld failure in the burner housing. To resolve this: 1. Turn the burner off and let it cool for at least two minutes. 2. Relight the burner and burn on high for at least five minutes, or until the ceramic tiles are evenly glowing red. 3. Ensure that no more than 75% of the grill surface is covered. 4. If cracks are found, contact your authorized Napoleon dealer to order a replacement burner assembly.
R
rlambertSep 12, 2025
Why are the flames lifting away from the burner on my Napoleon BIPRO 665?
- J
  John WagnerSep 12, 2025
  If the flames on your Napoleon Grill lift away from the burner, accompanied by the smell of gas and lighting difficulties, it is likely due to an improper air shutter adjustment. A qualified gas installer should slightly close the air shutter according to the combustion air adjustment instructions.