To Next PageTo Next PageWhat to do if the thermocouple is shorting on my Napoleon GD80NT Indoor Fireplace?
If the thermocouple on your Napoleon Indoor Fireplace is shorting or faulty, try loosening and tightening it. You can also clean the thermocouple and valve connection. If the problem persists, consider replacing the thermocouple or the valve.
Why is there carbon depositing on my Napoleon GD80NT?
If carbon is depositing on the glass, burner media, or combustion chamber surfaces of your Napoleon Indoor Fireplace, there might be a blockage in the vent. Remove any blockage. In very cold conditions, ice buildup may occur on the terminal and should be removed. To prevent this in the future, wrap vent lengths passing through unheated spaces with an insulated mylar sleeve. Also, ensure the air shutter opening is free of lint or other obstructions. Incorrect installation or over/under-firing of the unit could also be the cause, so refer to the venting section to ensure correct location of storm collars and check pressure readings: Inlet pressure can be checked by turning screw (A) counter-clockwise 2 or 3 turns and then placing pressure gauge tubing over the test point. Gauge should read 7...
Why is there no gas at the pilot burner of my Napoleon GD80NT Indoor Fireplace?
If there is no gas at the pilot burner of your Napoleon Indoor Fireplace, check that the manual valve is turned on and inspect the pilot orifice for blockage. If these steps don't resolve the issue, you may need to replace the valve or call the gas distributor.
How to adjust the spark gap on my Napoleon Indoor Fireplace?
If the spark gap is incorrect on your Napoleon Indoor Fireplace, adjust it to be 0.150” to 0.175” (5/32” to 11/64” approx.) from the electrode tip and the pilot burner.
What to do if my Napoleon Indoor Fireplace is out of propane gas?
If your Napoleon Indoor Fireplace is out of propane gas, fill the tank.
How to fix remote wall switch wire issues with my Napoleon GD80NT?
If the remote wall switch wire is too long, resulting in too much resistance in the system of your Napoleon Indoor Fireplace, shorten the wire to connect length or wire gauge.
What to do if the main burner orifice is plugged on my Napoleon Indoor Fireplace?
If the main burner orifice on your Napoleon Indoor Fireplace is plugged, remove the stoppage in the orifice.
How to troubleshoot defective wall switch wiring on my Napoleon GD80NT?
If the wall switch wiring on your Napoleon Indoor Fireplace is defective, disconnect the switch wires and connect a jumper wire across terminals 1 & 3. If the main burner lights, check the wires for defects and/or replace them.
How to check if the thermostat or switch is defective on my Napoleon Indoor Fireplace?
If the thermostat or switch on your Napoleon Indoor Fireplace is defective, connect a jumper wire across the wall switch terminals. If the main burner lights, replace the switch/thermostat.
What to do if I smell exhaust fumes from my Napoleon GD80NT?
If you smell exhaust fumes in the room or experience headaches when using your Napoleon Indoor Fireplace, ensure the exhaust bracket gasket is sealed properly. Also, check the door seal, look for any exhaust blockages, and verify that the venting is installed correctly.
Essential safety precautions for operation, installation, and general use of the appliance.
Detailed instructions for installing vent systems, including clearances, lengths, and components.
Procedures for connecting the gas supply, ensuring compliance with codes and safety.
Guidelines for framing enclosures and maintaining minimum clearances to combustibles.
Procedures for removing/installing the glass door and preparing for log placement.
Steps for installing decorative brick panels and correctly positioning logs for optimal flame.
Step-by-step guide for operating the appliance using the remote control and basic functions.
How to use remote functions like thermostat, flame height, fan speed, and smart thermostat.
Procedures for electrically connecting and grounding the appliance according to electrical codes.
Procedures for adjusting pilot burner flame size and venturi air shutter openings for optimal performance.
Regular cleaning of burner assembly, media, and checking seals for proper function and longevity.
Instructions for replacing the night light lamp and the circulating blower unit.
Solutions for common flame appearance issues, carboning, and pilot/burner ignition failures.
Details on the limited warranty, conditions, exclusions, and claim procedures.
Essential safety precautions for operation, installation, and general use of the appliance.
Detailed instructions for installing vent systems, including clearances, lengths, and components.
Procedures for connecting the gas supply, ensuring compliance with codes and safety.
Guidelines for framing enclosures and maintaining minimum clearances to combustibles.
Procedures for removing/installing the glass door and preparing for log placement.
Steps for installing decorative brick panels and correctly positioning logs for optimal flame.
Step-by-step guide for operating the appliance using the remote control and basic functions.
How to use remote functions like thermostat, flame height, fan speed, and smart thermostat.
Procedures for electrically connecting and grounding the appliance according to electrical codes.
Procedures for adjusting pilot burner flame size and venturi air shutter openings for optimal performance.
Regular cleaning of burner assembly, media, and checking seals for proper function and longevity.
Instructions for replacing the night light lamp and the circulating blower unit.
Solutions for common flame appearance issues, carboning, and pilot/burner ignition failures.
Details on the limited warranty, conditions, exclusions, and claim procedures.
General| Brand | Napoleon |
|---|---|
| Model | GD80NT |
| Category | Indoor Fireplace |
| Language | English |
