NEC NP901W - Projecting an Image (Basic Operation); Turning on the Projector

22
V
I
D
E
O
I
N
A
U
D
IO
I
N
U
S
B
L
A
N
A
U
D
I
O
I
N
H
D
M
I
I
N
A
U
D
I
O
I
N
C
O
M
P
U
T
E
R
/
C
O
M
P
O
N
E
N
T
2
I
N
C
O
M
P
U
T
E
R
/
C
O
M
P
O
N
E
N
T
1
I
N
P
C
C
O
N
T
R
O
L
M
O
N
I
T
O
R
O
U
T
A
U
D
I
O
O
U
T
S
-
V
I
D
E
O
I
N
A
U
D
IO
I
N
L/M
O
N
O
L/M
ON
O
R
R
A
C
I
N
U
S
B
L
A
M
P
S
T
A
T
U
S
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
3
D
R
E
F
O
R
M
S
E
L
E
C
T
(
L
A
N
)
U
S
B
WIRELESS
WIRELESS
USB
LAMP
STATUS
COMPUTER
VIDEO S-VIDEO
VIEWER
NETWORK
HDMI
PIP
MENU
EXIT
COMPONENT
AUTO ADJ.
1 32
4 65
7 98
0
CLEAR
POWER
ID
1 2 3
OFF ON
USB
LAMP
STATUS
SOURCE
AUTO ADJUST
3D REFORM
SELECT
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.

Turning on the Projector
NOTE:
• The projector has two power switches: a main power switch and a POWER button (POWER ON and OFF on the remote control).
• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (

) po-
sition. Failure to do so may cause damage to the projector.
• The projector has a feature to prevent itself from being used by unauthorized individuals. To use this feature, register a key-
word. (
→
page 43)
1. Remove the lens cap.
• Do not try to remove the lens cap by pulling on the
string. Doing so can cause damage.
2. To turn on the main power to the projector, press the
Main Power switch to the on position ( I ).
• The projector will go into standby mode. When in stand-
by mode, the POWER indicator will light orange and the
STATUS indicator will light green.
3. After making sure that the projector is in standby
mode, press the POWER or POWER (ON) button for
a minimum of 2 seconds when the STATUS indicator
goes off and the POWER indicator starts blinking.
When the POWER indicator turns a steady green,
and the projector is ready to use.
• After you turn on your projector, ensure that the comput-
er or video source is turned on and that your lens cap is
removed.
NOTE: When no signal is available, a blue, black or logo screen is displayed.
Standby Blinking Power On
Steady orange
light
Blinking green
light
Steady green
light
(
→
page 128)
Press this button for a
minimum of 2 seconds.
U
S
B
L
A
M
P
S
T
A
T
U
S
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
3
D
R
E
F
O
R
M
S
E
L
E
C
T