PS15, PS15TD MKII & LS1200 : SPECIFICATIONS, CURVES & DIAGRAMS
SYSTEM SPECIFICATIONS PS15 with PS15 TDcontroller MK2 LSub 1200 with PS15 TDcontroller MK2
Frequency Response [a] 50 Hz - 18 kHz ±3 dB 30 Hz - 120 Hz ±3 dB
Usable Range @-6 dB [a] 47 Hz - 18 kHz 29 Hz - 130 Hz
Sensitivity 1W @ 1m [b] 102 dB SPL Nominal. 99 dB SPL Wideband 102 dB SPL Nominal
Nominal Peak SPL @ 1m [b] 131 to 134 dB Peak (for 550 to 1200 W RMS Amp.) 133 to 135 dB Peak (800 to 1200 W RMS Amp.)
HF Dispersion [c] 50° to 100° Hor. x 55° Vert. Rotatable Horn - 4 positions -
Directivity : Q & DI [c] Q : 16 Nominal DI : 12 dB Nominal ( f > 1.5 kHz ) -
Crossover Frequencies 900 Hz Passive or Active (internally switchable) 80 Hz Active through PS15 TD
Nominal Impedance Passive : 8 Ohms or Active : LF : 6 Ohms & HF : 8 Ohms 6 Ohms
Recommended Amplifiers 550 to 1200 Watts into 8 Ohms for 1 x PS15 per channel
1000 to 1800 Watts into 4 Ohms for 2 x PS15 per channel
800 to 1200 Watts into 8 Ohms
-
SYSTEM SPECIFICATIONS PS15Bass with PS15 TDcontroller
Frequency Response 40 Hz - 300 Hz
Sensitivity 1W @ 1m 102 dB SPL Nominal. 99 dB SPL Wideband
Nominal Peak SPL @ 1m 131 to 134 dB Peak (for 550 to 1200 W RMS Amp)
Cutoff Frequency 120 Hz Passive - 6dB per Octave - Reactance compensation
Nominal Impedance 8 Ohms
Recommended Amplifiers 550 to 1200 Watts into 8 Ohms for 1 x PS15Bass per channel
1000 to 1800 Watts into 4 Ohms for 1 x PS15Bass + 1 x PS15 or 2 x PS15Bass per channel
SYSTEM OPERATION
Electronic Controller The PS15 TDcontroller is precisely matched to the PS15 & LS1200 cabinets and includes protections. Using
PS15 & LSub’s without a properly connected PS15 TD will result in poor sound quality and can damage the
components.
Dispersion configuration After quick-release of the front grille from its fixings, the HF Horn can be rotated in 4 positions for dispersion
configuration.
Subbass The PS15 can be used without optional Subbass. Active operation of the LS1000 is included in the PS15 TD.
Speaker Cables PS15 are wired 2- & 2+ on Passive Input Speakons, LS1000 on 1- & 1+. Loop through Speakons are present on
both. Single identical cables can thus be used to loop through combinations of PS15 in passive & LS1000 in no
particular order.
PRODUCT FEATURES PS15 LSub 1200
Components :LF [Sub]
HF
1 x 15" (38 cm) 6 Ohms proprietary
1 x 2" throat, 3" Titanium diaphragm, driver + Low Distortion,
Constant Directivity Asymmetrical Dispersion Horn.
1 x 18" (46 cm) long excursion 6 Ohm
proprietary driver
-
Height x Width x Depth 675 x 434 x 368 mm (26.57"x 17.08"x 14.48") 515 x 791 x 597 mm (20.28"x 31.14"x 23.50")
Dimensions of 2 stacked LS1200 = 1 x LS2000
Weight : Net 29 kg (64 Lb.) 45 kg (99 Lb.)
Speakon Connectors 2 x 4 pole (Passive In & Loop Thru) + 1 x 4 Pole (Active In) 2 x 4 pole (In & Loop Thru)
Construction Baltic Birch Ply finished with structured black coating Baltic Birch Ply & structured black coating
Fittings: Handles 2 Metal recessed pockets 2 Metal recessed pockets
Front finish Acoustic foam on hex perforated steel grille (77% transparent) Perforated steel grilles
Flying Points 1 steel anchor plate for flying track on top (9 positions).
2 steel anchor plates for flying tracks on bottom (3 positions)
3 steel anchor plates for flying tracks on sides
and back
Stand fittings Built in Steel Stand Fitting, 35 mm (1"3/8) Internal Steel Stand Fitting on Top (35 mm,
1"3/8) accepts a mast supporting 1 or 2 PS15's.
Fixed Installation One set of 4 fixing points (Omnimount 100 Std spacing)
To Next Page
Loading...
Need help?
General
