Nidek Medical TONOREF II Network Setting Manual

Nidek Medical TONOREF II

24 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

AUTO REF/KERATO/TONOMETER

Model

TONOREF II

NETWORK SETTING MANUAL

March, 2009

XRKT2*RDA002A/E

Table of Contents

Other manuals for Nidek Medical TONOREF II

Operator's Manual170 pages

Questions and Answers:

K
Karen JohnsonAug 19, 2025
What to do if the auto-tracking function doesn't work on Nidek Medical TONOREF II?
- D
  Dominique BennettSep 12, 2025
  If the auto-tracking or auto shot function isn't working on your Nidek Medical Measuring Instruments, here's what you can do: * Ensure the auto-tracking or auto shot function is turned on using the auto button. * If room illumination is reflecting on the cornea, change the location and try measurement again. * If the patient has conditions like keratoconus or has recently undergone corneal surgery, these functions may not work. Turn off the auto-tracking function and start measurement. * If the patient has substantial ocular ataxia or cannot fixate their eyes, turn off the auto-tracking function and start measurement. * If the device is near a window exposed to sunshine, relocate it to avoid light interference.
S
Shelby MooreAug 21, 2025
What to do if a measurement error appears on Nidek Medical TONOREF II?
- V
  Victoria ChapmanAug 21, 2025
  If you encounter a measurement error with your Nidek Medical Measuring Instruments, consider the following: * The patient may have blinked. Instruct them to avoid blinking during measurement. * Eyelids or eyelashes might be obstructing the measurement. Ask the patient to open their eyes wider, or gently lift the eyelid, being careful not to press on the eyeball. * If the pupil is too small, have the patient sit in a dark room to allow pupil dilation, then try again. * Ensure the patient is looking at the fixation lamp. * The data may exceed the measurable limit.
B
Brittany BurtonAug 23, 2025
What to do if data is not printed out from Nidek Medical TONOREF II?
- K
  Keith ValenciaAug 25, 2025
  If data isn't printing from your Nidek Medical Measuring Instruments, check these points: * Ensure the printer has paper. If it's empty, load new paper. * Verify that the '31. PRINT' parameter is not set to 'NO'. If it is, reset the parameter.
T
Travis BennettAug 26, 2025
Why is the LCD display not turning on for Nidek Medical TONOREF II?
- A
  Andrew SanchezAug 26, 2025
  If the LCD display on your Nidek Medical Measuring Instruments isn't turning on, check the following: * Make sure the power cord is securely connected. Reconnect it if necessary. * Verify that the power switch is turned on.
G
gardnerkarenAug 27, 2025
What to do if Nidek Medical TONOREF II printer paper does not feed?
- D
  Daniel KentAug 27, 2025
  If the printer paper isn't feeding in your Nidek Medical Measuring Instruments, it might be loaded incorrectly. Open the printer cover and ensure the paper is loaded properly, not tilted, and that the core of the roll is correctly placed.
K
Karen PerezAug 29, 2025
What to do if the main body of Nidek Medical TONOREF II Measuring Instruments cannot be moved laterally?
- W
  Wayne MillerAug 29, 2025
  If the main body of your Nidek Medical Measuring Instruments cannot be moved laterally, the locking lever may be locked. Flip up the locking lever.
M
Melissa WellsAug 31, 2025
What to do if Nidek Medical TONOREF II shows ERROR or NO PAPER even with paper loaded?
- P
  Peter CurrySep 1, 2025
  If your Nidek Medical Measuring Instruments displays “ERROR” or “NO PAPER” even when paper is loaded: * Ensure the printer cover is securely closed. Open and then securely close it. * Avoid pressing the print button immediately after closing the printer cover, as the printer needs time to get ready.
A
Amy GreerSep 3, 2025
Why do measurement values differ on Nidek Medical TONOREF II?
- L
  Laura CookeSep 3, 2025
  If you're getting different measurement values on your Nidek Medical Measuring Instruments, it could be due to the patient moving their visual line. Instruct them to focus on the fixation chart (center of the scenery chart for AR, KM measurements; fixation lamp for NT measurement). For patients who struggle to maintain their visual line, turn off the auto shooting function and manually press the start switch when their visual line is correct.
R
Ryan StewartSep 5, 2025
What to do if Nidek Medical TONOREF II Measuring Instruments prints 'CHECK MEASURING WINDOW' at start-up?
- D
  Douglas LopezSep 5, 2025
  If your Nidek Medical Measuring Instruments prints “CHECK MEASURING WINDOW” at start-up: * Clean the measuring window. * If the window is clean, ensure it's not blocked during start-up.
V
Veronica WoodsSep 7, 2025
What to do if the Nidek Medical TONOREF II Measuring Instruments printer operates but doesn't produce results?
- C
  conradhollySep 7, 2025
  If the printer on your Nidek Medical Measuring Instruments is running but not producing results, the printer paper may be loaded with the wrong side up. Ensure it's loaded with the correct side facing up.

Nidek Medical TONOREF II Specifications

General

Axis	1 to 180°
Accuracy (Automated dynamic contour tonometry)	±1 mmHg
Display	Color LCD touch screen
Power Supply	AC 100 to 240V, 50/60 Hz
Type	Auto Ref/Keratometer/Tonometer

Related product manuals

Preview: Nidek Medical LM-7

Nidek Medical LM-7

Preview: Nidek Medical ARK-1S

Nidek Medical ARK-1S

Preview: Nidek Medical LM-600

Nidek Medical LM-600

Preview: Nidek Medical LM-500

Nidek Medical LM-500

Nidek Medical AR-600A

Nidek Medical LM-600P

Nidek Medical AR-660A

Preview: Nidek Medical RT-5100

Nidek Medical RT-5100

Nidek Medical LM-1200

Preview: Nidek Medical YC-1800

Nidek Medical YC-1800

Nidek Medical ARK-700A

Preview: Nidek Medical ARK-700 Series

Nidek Medical ARK-700 Series