Why is there no phase contrast effect on my Nikon Microscope?
If you're not getting a phase contrast effect on your Nikon Microscope, ensure you're using a Ph objective. Also, check that the condenser annular diaphragm is in the optical path and matches the Ph code of the objective, and that it is centered. If using a system condenser, make sure the aperture diaphragm is fully open.
How to reduce eye fatigue when using a Nikon Microscope?
If you're experiencing eye fatigue while using the Nikon Microscope, start by making diopter adjustments. If the issue persists, adjust the brightness using the brightness adjustment dial or ND filters to ensure adequate brightness.
How to fix a yellowish image on my Nikon Microscope?
If your Nikon Microscope displays a yellowish image, the NCB11 filter might be missing from the optical path; insert it. If the issue remains, the lamp voltage may be too low; adjust the brightness adjustment dial to match the lamp ratings.
Why does the image flow on my Nikon ECLIPSE TE2000-S Microscope?
If your Nikon Microscope image flows, make sure the specimen is correctly positioned on the stage. Also, ensure the revolving nosepiece is correctly installed and rotated to the click stop position. In addition, center the condenser annular diaphragm and raise the dia-illuminator till it hits the limit.
What to do if the view field is too dark on my Nikon Microscope?
If your Nikon Microscope's view field is too dark, the condenser aperture diaphragm may be stopped down too far; normally, it should be set to 70 to 80% of the objective N.A. Also, ensure the field diaphragm image is correctly focused on the specimen surface by performing condenser focusing and centering. Finally, check that the optical path switchover dial is set to 100% observation.
How to improve poor image quality on Nikon ECLIPSE TE2000-S Microscope?
If you're experiencing poor image quality, contrast, or resolution with your Nikon Microscope, start by cleaning the lens and container to remove any dirt or dust. Ensure the objective’s correction ring is correctly set to the bottom plate thickness of the container. If the issue continues, verify that the bottom plate thickness of the container is within the objective's correction range, or perform condenser focusing and centering correctly.
Why is the view field too bright on my Nikon Microscope?
To address a view field that's too bright on your Nikon Microscope, first, insert an ND filter into the optical path. If the issue persists, lower the lamp voltage using the brightness adjustment dial.
Why can't I focus with 20x and 40x objective on my Nikon ECLIPSE TE2000-S Microscope?
If you cannot focus with 20x and 40x objectives on your Nikon Microscope, the bottom plate thickness of the container may be outside the correction range of the objective. Use a container with a bottom plate thickness within the correction range.
General| Type | Inverted Microscope |
|---|---|
| Stage | Mechanical Stage |
| Objective Lenses | CFI60 series objectives (various magnifications and N.A.) |
| Illumination | Halogen Lamp |
| Camera Compatibility | Digital Cameras |
| Focusing | Coarse and fine focusing |
| Nosepiece | 6-position nosepiece |
| Eyepiece Tube | Binocular / Trinocular |
| Power Supply | AC 100-240V, 50/60Hz |
| Optical System | Nikon CFI60 optical system |
Explains symbols used in the manual and on the equipment for safety.
Covers intended use, disassembly, voltage checks, heat, hazardous samples, and general safety.
Provides guidance on careful handling, proper installation location, and disposal of the microscope.
Details components and controls on the left and right sides of the TE2000-E microscope bases.
Lists adapters for front, side, and bottom ports for attaching external devices.
Describes the Dia-illuminators and Condenser modules for microscopy applications.
Covers stages, focusing modules, and rear-mounted components like controllers.
Explains the power supply units and their electrical specifications for operation.
Step-by-step guide for bright-field observation setup and execution.
Step-by-step guide for phase-contrast observation setup and execution.
Instructions for capturing images using a 35mm camera attached to the microscope.
Details power controls and how to direct the light path to different observation ports.
Explains methods for adjusting illumination intensity, using filters, and controlling diaphragms.
Covers objective handling, diopter adjustment, and focusing module operation.
Instructions for assembling the main body, eyepiece tube, and nosepiece.
Procedures for mounting the dia-illuminator, condenser, and installing the lamp.
Guides on connecting power cords and attaching devices to microscope ports.
Lists common optical and operational problems and their recommended solutions.
Addresses electrical issues like power, lamp, or brightness control problems and their countermeasures.
Lists technical specs for different microscope system combinations with illuminators.
Covers AC adapter, power cords, and certifications like FCC, EU Directives.
Visual representation of the TE2000-E system components and their interconnections.
Visual representation of the TE2000-U/TE2000-S system components and interconnections.
To Next Page