Why “DIS” appears on the status display panel of Nikon Eclipse Ti-E?
If “DIS” appears on the status display panel of your Nikon Microscope, place a specimen on the stage and focus on it manually. Rotate the focus knobs to move the objective closer to the boundary surface of the specimen. Use a specimen suited for PFS, noting that PFS will not function if the cover glass is too thick or if the refraction index of the solution is too high.
How to clean dirt or dust seen in Nikon Microscope's field of view?
If you're seeing dirt or dust in the field of view of your Nikon Microscope, it could be due to contaminants on the lens, other optical elements, or the culture vessel. Clean these optical elements and use a clean culture vessel. Also, ensure that the field diaphragm image is correctly focused on the specimen's focal plane by properly focusing and centering the condenser.
What to do if Nikon Eclipse Ti-E image quality is poor?
If you're experiencing poor image quality, contrast, or resolution with your Nikon Microscope, start by cleaning all optical elements and ensuring you're using a clean culture vessel. Check that the objective correction ring is properly matched to the culture vessel's bottom plate thickness, and that the vessel's thickness is within the objective's correction range. Finally, make sure the field diaphragm image is correctly focused on the specimen's focal plane by properly focusing and centering the condenser.
How to prevent eyestrain with Nikon Eclipse Ti-E?
If you're experiencing eyestrain during observations with your Nikon Microscope, adjust the diopters. Also, adjust the brightness of the lamp, or use ND filters to optimize the brightness.
Why focusing operation terminates after pressing the PFS-ON switch on Nikon Eclipse Ti-E?
If the focusing operation is terminated and the buzzer sounds approximately 5 seconds after pressing the PFS-ON switch on your Nikon Microscope, place a specimen on the stage and focus on it manually. Rotate the focus knobs to move the objective closer to the boundary surface. Ensure you are using a specimen suited for PFS, as it will not function correctly if the cover glass is too thick or if the refraction index of the solution is too high.
Why a long beep sounds during the perfect focus operation on Nikon Eclipse Ti-E Microscope?
If a long beep sounds during the perfect focus operation and the perfect focus function ends on your Nikon Microscope, and you're using a dry objective, PFS is turned off for safety if no boundary surface is detected within 5 seconds. Check that the PFS dichroic mirror is in the optical path. Ensure the nosepiece is in a click-stop position. Also, make sure the limit for vertical stage movement has not been reached. Verify that a glass-bottomed dish (No.1S) is used for the specimen. If a PFS internal error is indicated, contact Nikon.
How to fix dia illuminator lamp that does not light on Nikon Eclipse Ti-E?
If the dia illuminator lamp does not light on your Nikon Microscope, replace it with a specified lamp.
How to merge images in binocular eyepiece of Nikon Eclipse Ti-E Microscope?
If, when viewing through the binocular eyepiece of your Nikon Microscope, the images do not merge into a single image, adjust the interpupillary distance.
What to do if the lamp does not turn on/off on Nikon Eclipse Ti-E Microscope?
If the lamp on your Nikon Microscope does not turn on or off when you operate the dia illumination ON/OFF switch, replace the lamp with a specified lamp. Also, check the connection of the control cable.
Why is my Nikon Eclipse Ti-E image yellow-tinged?
If you observe a yellow-tinged image with your Nikon Microscope, move the ND filter into the optical path. You might also need to adjust the brightness control knob to match the lamp rating if the lamp voltage is too low.
General| Type | Inverted Research Microscope |
|---|---|
| Optical System | CFI60 infinity optical system |
| Software | NIS-Elements imaging software |
| Stage | Motorized stage |
| Camera Compatibility | Compatible with various Nikon digital cameras and 3rd party cameras |
| Objectives | Compatible with Nikon CFI60 objectives |
| Focusing | Motorized focus |
| Nosepiece | Motorized 6-position nosepiece |
| Applications | Live-cell imaging, fluorescence |
| Objective Turret | Motorized 6-position |
| Condenser | Motorized condenser |
| Observation Tubes | Binocular and trinocular observation tubes available |
| Camera Port | Multiple camera ports available |
| Dimensions | Varies depending on configuration |
| Weight | Varies depending on configuration |
Illustrates the Ti-E microscope body and its key accessories for identification.
Details the parts and features of the microscope base unit.
Describes the front, left, and right operation panels and their controls.
Identifies and describes the right and rear connector panels.
Details various eyepiece base units, tubes, and their features.
Introduces the PFS Motorized Nosepiece and PFS Offset Controller.
Describes the different types of stages available for attachment.
Details the types of dia pillar illuminators and condensers.
Describes the power supply units and the AC adapter.
Provides an overview of Ti series microscopes and microscopy procedures.
Explains the workflow and steps for bright-field microscopy.
Explains the workflow and steps for phase contrast microscopy.
Explains the workflow and steps for external phase contrast microscopy.
Details the in-focus observation method using the Perfect Focus System (PFS).
Explains procedures for powering the microscope and illumination on and off.
Covers the operation of the dia illumination system, including lamp and brightness.
Describes the functions of the controls on the microscope body's panels.
Explains optical path selection and filter operations.
Details operations for condensers and eyepiece tubes.
Covers focusing mechanism, objective operation, and related controls.
Details operations specific to the pillar illuminator and mechanical stage.
Explains the operation of the Perfect Focus System (PFS).
Lists required tools, installation conditions, and checks for assembly.
Details the steps for installing the microscope body (base).
Explains attachment of eyepiece base units and tubes.
Details attaching the dia pillar illuminator and condensers.
Covers connecting power supply, PFS controller, and AC adapter.
Explains how to register objective information for PFS functionality.
Lists problems related to image quality and viewing, with solutions.
Addresses issues encountered during microscope operation and their fixes.
Lists problems related to power and electrical components with solutions.
Troubleshoots issues specific to the PFS function and its indicators.
Details procedures for cleaning lenses and filters to maintain image quality.
Provides instructions for cleaning the microscope body and disinfection.
Gives guidelines for storing the microscope and recommends periodic inspections.
Lists technical specifications for TI-DH and TI-DS illuminator configurations.
Details specifications for the PFS Motorized Nosepiece and Offset Controller.
Lists specifications for AC adapter, power cords, and safety compliance.
To Next Page