Nuova Simonelli professional espresso machine - PROGRAM Vip Plus Model: Diagnostics and Maintenance; Grinding Control Alarms and Settings; Fault History and Maintenance Scheduling; Diagnostic Alarms and Error Codes

21
the display will show the message F I N E
G
RINDING (see the Diagnostics Section).
A
t this point, the grinder must be regulated
a
nd the grinding fineness increased.
If
values are set at 00-40, this function will
b
e excluded.
F
ault History
In
sert key U.
B
y pressing ▼ once, the display will read
F
AULT HISTORY. Press ENTER to display
E
RROR 01. By pressing the ▼ c o n s e c u t i-
v
ely the last ten errors held in memory will
b
e scrolled. After this has been viewed,
p
ressing ▼ again will display the next page.
M
aintenance schedule programming
T
he display will read M A I N T E N A N C E .
P
ress ENTER to display DELIVERIES and
D
AT E and set these values with the ▼ ▲
k
eys, pressing the ENTER key to confirm.
P
ress ENTER again to pass on to the next
p
age.
W
hen the set limit has been reached (the
fi
rst of the two), the display will read MAIN-
T
ENANCE.
In
sert the U-key (15) to set to zero with the
R
ESET key.
P
ress the ▼ key to pass on to the next
p
age.
L
anguage Select
T
he display will read LANGUAGE and by
p
ressing ENTER, the set language (ITALIA-
N
O or ENGLISH) will appear. Use the ▼▲
k
eys to change the selected language and
th
is will change instantly. Use the ENTER
k
ey to confirm the selection and to pass on
to
the following page.
D
isplay Functions with Keys 1-14
If
a key from 1-14 is inserted into the machi -
n
e, access will be given to the normal work
functions. The following menus will be
displayed but no modifications will be possi -
ble.
Coffee and Hot Water Doses
By pressing the ▼ key, the display will read
DOSES and all coffee and hot water leds
will flash. If selection is attempted (the key
led stays lit), the display will indicate that
the relative value cannot be modified. Use
the ▼ key to pass on to the following page.
Delivery Count
The display will read D E L I V E RY C O U N T
and all selection leds will flash. If a key rela-
tive to the selected dose is pressed (the
led stays lit), the number of deliveries made
will be displayed (the CONTINUOUS COF-
FEE function counts as one delivery). Use
the ▼ key to visualise the UNIT TO TA L.
The leds of SHORT ESPRESSO keys for
all units will flash and if one of these keys is
pressed (the led stays lit), the display will
show the total number of deliveries. Press
the ▼ key to display the MACHINE TOTAL
together with the total number of deliveries
Press ▼ to return to the normal display.
Diagnostics
Diagnosis Alarm
If, at the time of diagnosis, the system
encounters any malfunctions, the display
will read DIAGNOSIS ERROR, the func-
tions will be blocked and the machine will
not begin to heat up.
Delivery Alarm
Once the delivery time limit has been rea-
ched (120 sec.), if the flowmeter has not
transmitted the programmed number of
water counts, the display will flash D E L I-
V E RY ERROR and the led of the CONTI-
NUOUS key for the relative unit will also
flash. The display will return to its normal
configuration if RESET, or STOP is pressed
or a new selection is made.
Flowmeter Alarm
If, in the first 3 seconds, the flowmeter
sends no water counts, the display will flash
FLOWMETER ERROR and the led of the
CONTINUOUS key for the relative unit will
also flash. If delivery is not manually inter-
rupted then the automatic time limit lock
(120 sec.) will be triggered. The display will
return to its normal configuration if RESET
is pressed or a new selection is made.
Refill Alarm
If, 90 seconds from the start of filling, the
refill level has not been reset, the display
will flash REFILL ERROR, the pump will be
automatically disabled and all functions will
be inhibited.
The functions can be restarted by switching
the machine first off and then on again.
Excess Pressure Alarm
When the boiler temperature exceeds
125°C, the cup warmer is started automati-
cally and the resistance is stopped (the
system resets itself when the temperature
drops to below 125°C) and the display will
flash PRESSURE ERROR.
Grinding Alarm
When the grinding control system detects
values which differ from those programmed,
the display will read FINE GRINDING if it is
necessary to increase the grinding fine-
ness, or ROUGH GRINDING in the opposi-
te case. The display will return to its normal
function configuration if RESET, STO P, is
pressed or a new selection is made.
Please Note: If the machine is left in the
programming state, after 10 minutes, the
system will return to its original configura -
tion and the display will indicate normal
functioning.