CD Player Operation (continued)
STOPPING THE CD OPERATION
1. Press the STOP key on the master station to stop the CD Player. The current PLAY
mode (Repeat One, Repeat All, Random) and DISPLAY mode will remain.
2. Once the CD door is opened, the PLAY mode will automatically return to NORMAL
PLAY, and the DISPLAY mode will return to the TIME display.
REMOVING CD DISC FROM PLAYER
Note: Be sure hands are clean when handling discs.
1. Press the OPEN key on the master station. The door will pop open slightly.
2. Completely open the door by gently moving it from left to right.
3. Securely place your fingers around the outside edge of the disc, using the recessed
area around the disc.
4. Gently pull on the in the disc until it snaps away from the CD Player spindle.
5. Close the door by moving it from right to left until it latches closed.
Note: To keep laser-pickup clean, do not forget to close and latch door.
CD Operating Selection Modes
REPEAT PLAY: One Track
1. While the CD is playing, press the RDM/RPT key to
change the normal play mode to Repeat the
selected track.The letters ONE RPT will display, and
the track will continue to play until deactivated.
2. Press the RDM/RPT key three more times to end one repeat play. Normal forward
play continues from that point.
3. If the CD Player is stopped and restarted while in the ONE RPT mode, the last track
played will be the first tracked played once the player restarts.
4. Pressing STOP discontinues play of the CD Player.
5. Anytime the CD door is opened, the play mode will change to the normal
play mode.
REPEAT PLAY: All Tracks
1. While the CD is playing, press RDM/RPT key 2 times
to change from normal play mode to All Repeat
mode. The letters ALL RPT will display, and the
complete CD will continue to repeat play until
deactivated.
2. Press the RDM/RPT key two more times to end all repeat mode. Normal play
continues from that point.
3. If the CD Player is stopped and restarted while in the ALL RPT mode, the last track
played will be the first tracked played once the player restarts.
4. Pressing STOP discontinues play of the CD Player.
5. Anytime the CD door is opened, the play mode will change to the normal
play mode.
9
12
Controlling the CD Player & Radio from
Remote Stations (continued)
ADVANCING THE RADIO MEMORY CHANNELS
The radio memory channels may be advanced from a remote station by momentarily
pressing the AM/FM/CD CONTROL/END CALL key, while the AM or FM radio is
playing. Channels must be stored into memory before this feature is useful.
1. Place the Radio in the ON position by pressing the AM or FM key at the master
station or activating the radio from a remote station. (See: T
urning the Radio On
and Off.)
2. Quickly press the AM/FM/CD CONTROL/END CALL key. The radio will advance to
the next highest stored memory channel.
3. Press the AM/FM/CD CONTROL/END CALL key again for the next highest stored
memory channel. Each press represents the next stored channel.
4. After reaching the highest stored channel in the current program mode (AM or FM),
momentarily pressing the AM/FM/CD CONTROL/END CALL again will cause the
current program mode to switch to the opposite mode and select the lowest
programmed memory channel.
Example:
Current mode is FM
Press AM/FM/CD CONTROL/END CALL once = Memory Channel #5@104.9MHZ
Press AM/FM/CD CONTROL/END CALL again = Memory Channel #6@107.9MHZ
Next AM/FM/CD CONTROL/END CALL press = AM Mode, Memory Channel #1
@ 550 KHz
5. Continue pressing AM/FM/CD CONTROL/END CALL to reach the desired stored
memory channel.
TURNING THE CD PLAYER ON AND OFF
Note: A disc must be properly installed into the Master station CD Player and the
CD door must be properly closed, or this feature is inactive.
1. To turn the CD Player ON or OFF, press and hold the AM/FM/CD CONTROL/END
CALL key for 4 seconds.
2. At the end of 2 seconds, the radio will turn on. Continue holding in the AM/FM/CD
CONTROL/END CALL key.
3. Next you will hear the radio turn off and a ‘BEEP-BEEP’.
4. The ‘BEEP-BEEP’ sound will be heard throughout the system indicating that the CD
Player has been selected to the Play mode.
5. Release the AM/FM/CD CONTROL/END CALL key. In a few moments, the CD will
begin playing.
6. While the AM/FM/CD CONTROL/END CALL key is pressed at the controlling remote,
the Master station will display the letters IU (in use). This indicates that a control
function is currently being performed at a remote station.
ADVANCING THE CD PLAYER TO THE NEXT TRACK
1. Place the CD Player in the PLAY position by pressing the PLAY/PAUSE key at the
master station or activating the CD Player from a remote station. (See: Turning the
CD Player On and Off.)
2. Quickly press the AM/FM/CD CONTROL/END CALL key.The disc will advance to the
next highest track.
3. Press the key again for the next highest track. Each press represents the next highest
track.
▼▼
▼▼
▼▼
▼▼
▼▼
▼▼
▼▼
To Next Page
Loading...
Need help?
General
