Nyle e360 - Page 34

HeatWater.com | WaterService@nyle.com | (800) 777-6953 | Rev. IM-E360-060523
Installation: Condensate Piping
33
D7-Condensate Piping Diagram
A
3"
6"
DETAIL A
SCALE 1 : 8
VENT ABOVE DRAIN PAN
MIN. 3/4" PIPE •
1/4" PER FOOT MIN. SLOPE •
INSULATION & HEAT TRACE REQUIRED IN FREEZING CLIMATES •
TO CONDENSATE PUMP,
INDIRECT CONNECTION TO SEPTIC,
OR FROST PROTECTED DRAIN
INSTALL VENT AND TRAP ASSEMBLY IN FROST PROTECTED AREA
REVISIONS
REV. DESCRIPTION DATE APPROVED
8
B
1
36
C
D
B
3 16
1 OF 2
4/20/2023
GH
UNLESS OTHERWISE SPECIFIED:
1:32
TITLE:
NAME
DATE
CHECKED
DRAWN
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16"
DECIMAL
0.02"
ANGULAR MACH
1/2°
ANGULAR BEND
1°
PROPRIETARY AND CONFIDENTIAL:
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
NYLE SYSTEMS LLC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF NYLE SYSTEMS
LLC IS PROHIBITED.
DEPT:
WEIGHT (lbs):
8 7 5 4 2
D
A
7 5 4
2
A
C
SCALE:
SHEET:
SECTION:
PART REVISION:
SHEET SIZE:
B
2281.7403975
EDITED
GH
4/26/2023
E360 MANUAL
CONDENSATE DRAIN
B
3"
6"
DETAIL B
SCALE 1 : 8
VENT ABOVE DRAIN PAN
MIN. 3/4" PIPE •
1/4" PER FOOT MIN. SLOPE •
INSULATION & HEAT TRACE REQUIRED IN FREEZING CLIMATES •
TO CONDENSATE PUMP,
INDIRECT CONNECTION TO SEPTIC,
OR FROST PROTECTED DRAIN
INSTALL VENT AND TRAP ASSEMBLY IN FROST PROTECTED AREA
REVISIONS
REV. DESCRIPTION DATE APPROVED
8
B
1
36
C
D
B
3 16
2 OF 2
4/20/2023
GH
UNLESS OTHERWISE SPECIFIED:
1:32
TITLE:
NAME
DATE
CHECKED
DRAWN
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16"
DECIMAL
0.02"
ANGULAR MACH
1/2°
ANGULAR BEND
1°
PROPRIETARY AND CONFIDENTIAL:
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
NYLE SYSTEMS LLC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF NYLE SYSTEMS
LLC IS PROHIBITED.
DEPT:
WEIGHT (lbs):
8 7 5 4 2
D
A
7 5 4
2
A
C
SCALE:
SHEET:
SECTION:
PART REVISION:
SHEET SIZE:
B
2281.7403975
EDITED
GH
4/26/2023
E360 MANUAL
CONDENSATE DRAIN(2)
B
3"
6"
DETAIL B
SCALE 1 : 8
VENT ABOVE DRAIN PAN
MIN. 3/4" PIPE •
1/4" PER FOOT MIN. SLOPE •
INSULATION & HEAT TRACE REQUIRED IN FREEZING CLIMATES •
TO CONDENSATE PUMP,
INDIRECT CONNECTION TO SEPTIC,
OR FROST PROTECTED DRAIN
INSTALL VENT AND TRAP ASSEMBLY IN FROST PROTECTED AREA
REVISIONS
REV. DESCRIPTION DATE APPROVED
8
B
1
36
C
D
B
3 16
2 OF 2
4/20/2023
GH
UNLESS OTHERWISE SPECIFIED:
1:32
TITLE:
NAME
DATE
CHECKED
DRAWN
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16"
DECIMAL
0.02"
ANGULAR MACH
1/2°
ANGULAR BEND
1°
PROPRIETARY AND CONFIDENTIAL:
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
NYLE SYSTEMS LLC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF NYLE SYSTEMS
LLC IS PROHIBITED.
DEPT:
WEIGHT (lbs):
8 7 5 4 2
D
A
7 5 4
2
A
C
SCALE:
SHEET:
SECTION:
PART REVISION:
SHEET SIZE:
B
2281.7403975
EDITED
GH
4/26/2023
E360 MANUAL
CONDENSATE DRAIN(2)
A
3"
6"
DETAIL A
SCALE 1 : 8
VENT ABOVE DRAIN PAN
MIN. 3/4" PIPE •
1/4" PER FOOT MIN. SLOPE •
INSULATION & HEAT TRACE REQUIRED IN FREEZING CLIMATES •
TO CONDENSATE PUMP,
INDIRECT CONNECTION TO SEPTIC,
OR FROST PROTECTED DRAIN
INSTALL VENT AND TRAP ASSEMBLY IN FROST PROTECTED AREA
REVISIONS
REV. DESCRIPTION DATE APPROVED
8
B
1
36
C
D
B
3 16
1 OF 2
4/20/2023
GH
UNLESS OTHERWISE SPECIFIED:
1:32
TITLE:
NAME
DATE
CHECKED
DRAWN
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16"
DECIMAL
0.02"
ANGULAR MACH
1/2°
ANGULAR BEND
1°
PROPRIETARY AND CONFIDENTIAL:
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
NYLE SYSTEMS LLC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF NYLE SYSTEMS
LLC IS PROHIBITED.
DEPT:
WEIGHT (lbs):
8 7 5 4 2
D
A
7 5 4
2
A
C
SCALE:
SHEET:
SECTION:
PART REVISION:
SHEET SIZE:
B
2281.7403975
EDITED
GH
4/26/2023
E360 MANUAL
CONDENSATE DRAIN
Condensate Piping Requirements:
1. At least ¼” pitch per horizontal foot toward drain or freeze protected condensate
pump.
2. Minimum ¾” pipe size.
3. Insulation and heat tracing on all piping exposed to freezing temperatures.
4. All condensate pipes should include a trap with at least 3” standing water height in
freeze protected conditions.
5. All traps require a vent immediately downstream from the trap. Vents should extend to
a point higher than the bottom of the heat pump. Vents must be in a freeze protected
space.
6. Condensate pumps require their own trap and vent piping, and an indirect piping
connection from the heat pump condensate discharge pipe. Vent pipes need to
terminate higher than the condensate pump.
7. Any drain connection to septic requires an indirect connection and trap. Pay special
attention to all local codes and ordinances if connecting to septic.
8. When multiple units are connected to the same condensate piping, Nyle recommends
the use of isolation valves to allow blowing out of individual lines when necessary.