How to fix Error writing to Prn1 on Oki Printer?
If you receive an 'Error writing to Prn1' message on your Oki Printer, here are a few things to check: * Make sure the printer is online. * If the error indicates a paper shortage, add more paper and cancel the error. * Check if another user is currently printing; if so, wait until they are finished before printing.
What to do if the wireless connection is unsuccessful with specific wireless computers Oki Printer Accessories?
If you're experiencing unsuccessful wireless connections with specific computers, even when using the same wireless LAN settings, consider these possible causes: * The wireless computer network settings may be inappropriate. Ensure network settings like the IP address are correctly configured, even in Ad-Hoc mode. * The wireless function of the wireless computer might be off. Activate the wireless function setting on the affected computer. * A wired LAN interface might be interfering. If both wired and wireless interfaces are active, the application/utility might be using the wired connection. Deactivate the wired LAN interface on the wireless computer. * The wireless computer might be set to High Speed Mode. Turn off the high-speed transfer mode setting on the wireless computer.
How to fix EEPROM Check registers NG on Oki C9600dn?
If you encounter an 'EEPROM Check registers NG' error on your Oki Printer, try the following: * Confirm that the NIC is installed correctly, and then turn the printer off and on again. * Initialize the NIC.
Why is the printing light on my Oki All in One Printer?
If printing is light on your Oki All in One Printer, several factors could be responsible. First, ensure the toner cartridge is correctly installed by reinstalling it. If the issue persists, the toner may be low, requiring a replacement. Also, check the paper; if it's moist, use paper stored in proper temperature and humidity conditions. Ensure you're using paper recommended for the printer. Finally, adjust the printer settings for paper thickness and type via the [Media Weight] and [Media Type] options in the menu setup, potentially setting a thicker value for [Media Weight]. If you are using recycled paper, set one value thicker for [Media Weight] in the menu setup.
What to do if defect or type related characteristic of the Oki C9600dn Printer Accessories wireless computer or the wireless card mounted in the computer?
To address potential defects or type-related characteristics of the wireless computer or card: * Search for similar issues and solutions on the wireless computer or wireless card vendor's website. * Update the device drivers and wireless client software of the wireless computer to the latest versions. * If wireless communication remains unstable, consider replacing the wireless computer due to potential compatibility issues with the printer.
What to do if vertical lines appear on Oki All in One Printer prints?
If vertical lines appear on prints from your Oki All in One Printer, it could be due to a damaged image drum cartridge, which would require replacement. Alternatively, the toner might be low, necessitating a toner cartridge replacement.
What to do if Oki All in One Printer display panel doesn't work?
If the printer display panel of your Oki All in One Printer does not display anything or remains in standby mode 10 minutes after being switched on, follow the printer shutdown sequence to switch it off. Check all cable connections before restarting the printer. If the problem persists, contact your dealer.
What to do if Oki C9600dn is not identified by the Chooser and the Setup Utility?
If your Oki Printer is not identified by the Chooser and the Setup Utility, here are a few steps you can take: * Turn the printer off and on again. * Make sure the network cable is correctly connected, and try changing the cable. * If the network resides in a Zone, ensure the correct Zone name is selected in the Chooser. * Verify that the Zone name in the utility related to the NIC is the same as the Zone name set in the NIC. * Ensure AppleTalk (or Network in some OS versions) is set to Enable at the bottom right of the Chooser. * Make sure Ethernet is selected in AppleTalk (or Network). * Confirm the print driver is selected in the Chooser. * Ensure the EtherTalk protocol is set to Enable. * Print the NIC settings and confirm that the EtherTalk Port name is not blank.
How to fix Oki Printer cannot find the network interface card?
To resolve the issue of your Oki Printer not being able to find the network interface card, try the following: * Turn the printer off and on again. * Confirm that the network interface is enabled on the printer. * Ensure there is a response to the interface card command. * Make sure the network cable is correctly connected; change the cable and try again if needed. * Run the Self-diagnostic test (with the printer on, press and hold the Test button on the print server for 3 seconds, then release it). * Verify that the IP Address, Subnet Mask, and Gateway are correct. * Ensure that the TCP/IP protocol is set to Enable. * Reset the network interface card to the factory default settings. * If DHCP, BOOTP, and RARP are not used, ensure they have been set to Disable.
What to do if I have connection problems for wireless devices with my Oki All in One Printer?
If you're experiencing connection issues between your Oki All in One Printer and wireless devices, there are several things to check. The issue might stem from the access point devices or the wireless computers themselves. Ensure you have the latest firmware for your access point devices and the latest drivers for your wireless computer. Also, the access point device may be set to “High-Speed Mode;” try disabling this setting. If MAC Address Filtering is enabled on your access point, register the wireless card’s MAC address in the MAC Address Filtering list. Finally, multiple access points might have the same SSID. Check the SSID of access point devices in the surrounding area, including floors above and below, and check for any unauthorized access points.
General| Printer Type | Color Laser Printer |
|---|---|
| Print Resolution | 1200 x 1200 dpi |
| Max Resolution (DPI) | 1200 x 1200 dpi |
| Monthly Duty Cycle | 150, 000 pages |
| Duplex Printing | Yes |
| Network Connectivity | Ethernet |
| USB Connectivity | Yes |
| Connectivity | Ethernet, USB |
| Supported Media Sizes | A4, A5, B5, Legal, Letter |
To Next Page
