To Next PageTo Next PageWhat to do if Olimpia splendid SILENT 10 P Air Conditioner does not work?
If your Olimpia Splendid air conditioner isn't working, here's what to check: * Ensure the unit is plugged in. * Make sure there is power. * Verify the timer is switched off. Wait if there was a power outage.
Why Olimpia splendid SILENT 10 P works only for a short period?
Your Olimpia Splendid air conditioner might be working only for a short period of time due to these reasons: * The set temperature is too close to the ambient temperature; try lowering the set temperature. * The suction of outside air is obstructed; remove any obstructions.
Why Olimpia Splendid Air Conditioner works but does not refresh the room?
If your Olimpia Splendid air conditioner is running but not cooling the room effectively, consider these factors: * Close any open windows. * Eliminate sources of heat in the room, such as burners or lamps. Also, reduce crowding. * Lower the set temperature on the air conditioner. Note that the unit's power might not be suitable for the room's conditions or size.
What to do if alarm signal “ Fi “ appears on Olimpia Splendid Air Conditioner control panel display?
If the alarm signal “ Fi “ appears on the display of your Olimpia Splendid air conditioner, it means that the filter is dirty. Clean the filter. If the issue persists, switch the appliance back on and press button SW7 on the control panel for 5 seconds so that the alarm signal disappears from the display.
What to do if Olimpia splendid SILENT 10 P is off, the number “3” flashes on the control panel display and the red LED is on?
If your Olimpia Splendid air conditioner is off, the number “3” is flashing on the control panel, and the red LED is on, it indicates excessive water accumulation inside the unit. Drain the water by removing the cap (24). If this alarm occurs frequently, contact the service center.
What causes water leaks from Olimpia Splendid Air Conditioner during transport?
If water leaks from your Olimpia Splendid air conditioner during transport, it's likely because the unit has been tilted or laid flat. To resolve this, remove the plug (24) and drain the water before moving the conditioner.
Why minimum speed cannot be selected in Olimpia splendid SILENT 10 P?
If you cannot select the minimum speed in cooling, night-time, or automatic mode on your Olimpia Splendid air conditioner, it is normal behavior when the ambient temperature is too low.
Why Olimpia splendid SILENT 10 P stops the compressor in heating mode?
If your Olimpia Splendid air conditioner stops the compressor or the external fan cyclically for a few minutes in heating mode, it is normal behavior when the ambient temperature is too low or too high.
General| Brand | Olimpia splendid |
|---|---|
| Model | SILENT 10 P |
| Category | Air Conditioner |
| Language | English |
Provides introductory details about the appliance.
Explains icons and images used in the manual for clear communication.
Essential safety precautions for electrical equipment use.
Outlines the intended and correct usage of the air conditioner.
Specifies environments where the appliance should not be installed.
Details safety precautions related to the R290 refrigerant.
Identifies all parts included with the appliance.
Labels and describes the primary parts of the appliance.
Instructions for safe movement and handling of the appliance.
Crucial warnings to ensure proper and safe installation.
Procedures for installing the appliance in various window types.
Steps for safely connecting the appliance to the power supply.
Guidance on connecting the condensation discharge pipe.
Explains symbols and keys on the appliance's control panel.
Details the buttons and operations of the remote control.
How to use the remote control, including battery insertion.
Describes cooling, ventilation, dehumidification, and other modes.
Instructions for setting delayed switch-on and switch-off timers.
Guides for cleaning the appliance, remote, and filters.
Tips to reduce energy consumption.
Procedures for long-term storage and checks before reuse.
Explains error messages and their solutions.
Solutions for common malfunctions and issues.
