Olympus bx40 - Page 29

BX40
You are not using the specified immer- | Use the oil provided. 19
* Image is not sharp. | sion oil.
*
Contrast
is
poor.
|
ーー
ου
ーーーーー
ーー
ss
Li
+ Details are indistinct. | Specimen is dirty. Clean. |
|
Cendenser
is
dirty.
|
|
|
The slide glass or caver glass thickness | Change to glass of appropriate thickness. | 12
is not appropriate. |
|
i
T
g) Part of the image is | The objective is not properly positioned | Make sure that the objective clicks proper- | 8
blurred. in the light path. | ly into place. |
>
|
=
The specimen is not properly mounted Put the specimen properly on top of the
| on the stage. | stage and secure it properly with the | 12
| specimen clamp.
h) The image appears to | The objective is not properly positioned | Make sure that the objective clicks prope- | 8
‘waver. in the light path. ly into place. |
|
| The condenser is not properly centered. Center the condenser. | 16
|
,
]
i) The field of view be- | The condenser is not properly centered, Center the condenser. 16
cores
only
plot
1
nahr when the volt-
age is ЗЕ. | The condenser is lowered too far. | Adjust the condenser position. 16
2. Electrical System
a) The bulb intermittentiy | The bulb is nearly burned out. | Replace the bulb. s
lights
and
goes
out.
-二
E
A
connector
is
not
properly
connected.
|
Check
all
connections.
—
b)
The
bulb
burns
out
|
You
are
using
the
wrong
type
of
bulb.
|
Use
a
bulb
of
the
rated
type.
1
3
almost
immediately.
|
c)
Light
intensity
does
not
|
The
light
preset
button
is
set
ON.
Press
the
button
to
OFF.
change when you move 10
the "iont intensity lever.
n N |
d)
The
voltage
indicator
|
The
voltage
selector
switch
is
set
to
|
Set
the
switch
to
the
position
matching
LEDs
do
not
light,
or
the
|
the
wrong
position.
to
the
local
line
voltage
(100
—120V
or
|
5
bulb
does
not
light
|
|
220-240
|
e)
The
voltage
indicator
|
The
halogen
bulb
is
not
installed.
Install
the
bulb.
|
8
LEDs
all
light,
and
are
¡—
+
+
not
affected
by
the
light
|
The
bulb
is
burned
out.
|
Replace
the
bulb.
|
3
intensity lever. =
|
The
lamp
housing
output
connector
is
|
Properly
connect
the
lamp
housing
output
|
3
|
disconnected
connector
3.
Coarse/Fine
Focus
Adjustment
He
a)
The
coarse
adjustment
|
The
tension
adjustment
ring
is
over-
|
Loose
the
ring.
18
knob
is
hard
to
turn
tightened.
_
do
|
You
are
trying
to
raise
the
stage
with
|
Unlock
the
stopper
|
the
coarse
adjustment
knob
even
|
18
|
though
the
coarse
adjustment
stopper
|
Lis locked. | ー =
= |
b)
The
stage
goes
down
|
=
|
by
itself,
or
focus
is
lost
The
tension
adjustment
ring
is
too
loose.
Tighten
the
ring.
=
in the course of ob- |
servation. |
Table 7
—
25
o
30109
wwooreaanou
FA)