How to fix Omron Controller failed to create command log file?
If the Omron Controller fails to create a command log file, it may be because the specified file is read-only or the disk space is low. Increase the disk space or change the destination for creating the log file.
How to fix Omron Controller communications error with CX-Simulator Ladder Engine?
If a communications error occurs with the Omron Controller CX-Simulator Ladder Engine, it might be due to a wrong communications environment. Try the following: 1. Disconnect and then connect again. 2. Exit any running application programs except for the CX-Simulator. 3. Uninstall and then reinstall the CX-Simulator.
What causes Omron Controller to fail to read the PLC data file?
If the Omron Controller fails to read the PLC data file, it could be because the set file is broken. Reset the set file in the setting wizard to resolve this.
What to do if Omron Controller failed to start FinsGateway?
If Omron Controller's FinsGateway fails to start, it might be due to incorrect installation or invalid settings. Re-install the CX-Programmer, CX-Server, or FinsGateway to resolve this issue.
Why Omron Controller failed to start Data Replay Tool?
If the Omron Controller Data Replay Tool fails to start, it may be due to a wrong execution environment. To resolve this, follow these steps: 1. Exit any running application programs except the CX-Simulator and try again. 2. Uninstall and then reinstall the CX-Simulator.
How to fix Omron Controller failed to start Log display application?
If the Omron Controller Log display application fails to start, it may be due to a wrong execution environment. Try the following: 1. Exit any running application programs except for the CX-Simulator and try again. 2. Uninstall and then reinstall the CX-Simulator.
What causes Omron Controller to fail to gain access rights of CX-Simulator Ladder Engine?
If the Omron Controller CX-Simulator Ladder Engine fails to gain access rights, it could be because another application program is writing to the UM. Wait until the writing application program is completed, and then try again.
Why Omron Controller failed to save PLC data file?
If the Omron Controller fails to save the PLC data file, it may be due to low hard disk space or lack of access rights. Verify that the hard disk has sufficient space and that the user has authorization to write files.
What to do if Omron Controller failed to start I/O Condition Tool?
If the Omron Controller I/O Condition Tool fails to start, it may be due to poor resources or a wrong execution environment. Try these steps: 1. Exit any running application programs except the CX-Simulator and try again. 2. Uninstall, then reinstall the CX-Simulator.
Why does Omron Controller show an error while initializing Debugger startup?
If an error occurs while initializing the Debugger startup on the Omron Controller, it may be due to a wrong execution environment. To resolve this: 1. Exit any running application programs other than the CX-Simulator, and try starting the Debugger again. 2. If the issue persists, uninstall and then reinstall the CX-Simulator.
General| Manufacturer | Omron |
|---|---|
| Category | Network Hardware |
| Mounting | DIN Rail |
| Type | PLC |
| Series | CS Series |
| Programming Language | Ladder Diagram, Instruction List, Function Block Diagram, Structured Text, Sequential Function Chart |
| Communication Ports | Ethernet |
| Protocols Supported | Modbus, Ethernet/IP |
| Power Supply | 24V DC or 100-240V AC |
| Operating Temperature | 0°C to 55°C |
| Storage Temperature | -25°C to 65°C |
| Humidity Range | 10% to 90% (non-condensing) |
| Vibration Resistance | 10 to 57 Hz, 0.075 mm amplitude; 57 to 150 Hz, 1 G |
| Shock Resistance | 150 m/s² (15 G) in X, Y, and Z directions 3 times each |
To Next Page
