Onan RDJF Series - Page 59

GENERATOR GROUP - BEGIN SPEC AA
REF.
NO.
PART
NO.
QTY.
USED
PART
DESCRIPTION
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
STATOR, WOUND
220-2027 '
220-2209
220-2234
220-2019
220-2201
220-2226
220-2052
220-2159
220-2184
220-2044
220-2151
220-2176
201-2159
510-0112
232-2398
201-2151
515-0094
870-0284
205-0105
515-0103
526-0008
870-0131
358-0069
358-0070
853-0008
813-0100
211-0237
220-2009
COVER, END BELL
234-0185
234-0223
234-0498
1 Phase, 50 Hertz (AC) - 12 Volt (DC)
1 Phase, 50 Hertz (AC) - 24 Volt (DC)
1 Phase, 50 Hertz (AC)-32 Volt (DC)
1 Phase, 60 Hertz (AC) -12 Volt (DC)
1 Phase, 60 Hertz (AC) - 24 Volt (DC)
1 Phase, 60 Hertz (AC)- 32 Volt (DC)
3 Phase, 50 Hertz (AC) -12 Volt (DC)
3 Phase, 50 Hertz (AC) - 24 Volt (DC)
3 Phase, 50 Hertz (AC) - 32 Volt (DC)
3 Phase, 60 Hertz (AC) -12 Volt (DC)
3 Phase, 60 Hertz (AC) - 24 Volt (DC)
3 Phase, 60 Hertz (AC) - 32 Volt (DC)
Rotor Assembly, Wound -
Includes parts marked +
+Bearing, Rotor
+Spacer, Bearing
+Rotor, Wound - Exciter
+Key, Exciter Rotor
+Nut, Exciter Rotor Locking
+Fan, Generator
+Key, Fan
+Washer, Flat
+Nut, Hex (#10-32)
+Rectifier Assembly (Positive)
+Rectifier Assembly (Negative)
+Washer, Shakeproof (#10)
+Screw, Round Head (#10-32 x 1/2")
Bell, End
Stator, Wound - Exciter
Unhoused Sets
Housed Sets
Housed and Unhoused Sets with
Overspeed Switch
+ - Included in the Rotor Assembly.
REF.
NO.
PART QTY. PART
NO. USED DESCRIPTION
1 Seal, Bearing ("O" Ring)
4 Stud, Generator Through
4 Generator Through Stud (3/8")
2 End Bell Cover Mounting (1/4")
2 Resistor Bracket Mounting (1/4")
1 Rotor Through Stud (7/16")
1 Resistor Through Screw (1/4")
4 '•Air Baffle Mounting (#10)
4 Generator Through Stud (3/8-16)
1 Rotor Through Stud (7/16-20)
1 Resistor Tap (#10-32)
19 509-0094
20 520-0799
21 WASHER.LOCK
850-0050
850-0040
850-0040
850-0055
850-0040
850-0030
22 NUT, HEX
_ 862-0011
"870-0203
871-0010
23 WASHER, FLAT
526-0260
526-0034
2 Exciter Stator Mounting
1 Rotor Through Stud
24 WASHER, SHAKEPROOF
853-0013 2 Exciter Stator Mounting (1/4")
2 End Bell Cover Mounting (#10)-
1 Resistor Tap (#10)
25 800-0004 2 . Screw, Hex Cap - Exciter Stator
Mounting (1/4-20 x 5/8")
26 SCREW, ROUND HEAD
812-0165 2 End Bell Cover Mounting
(1/4-20 x 4-1/2")
2 End Bell Cover Mounting
(#10-32 x 3/8")
4 Air Baffle Mounting
(#10-32x3/8)
2 Resistor Bracket Mounting
(1/4-20 x 5/8)
1 ResistorThrough (1/4-20x5-1/2")
1 Resistor Tap (#10-32 x 3/8")
27 520-0791 1 Stud, Rotor Through
853-0008
856-0003
800-0004
813-0100
813-0098
812-0150
812-0169
811-0098
520-0791
58