EasyManua.ls Logo

onga JS100 - User Manual

onga JS100
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OWNER’S MANUAL
Should you the installer or owner be unfamiliar with the correct
installation or operation of this type of equipment you should contact
the distributor for the correct advice before proceeding with the
installation or operation of this product.
Jet Assisted Pumps
1000 Series
JMM100 JS100 JSM100 JSK110
JS110 JSP110 JSK120
JS120 JSP120
We recommend, for additional protection, the pump
to be supplied from socket outlet protected by a
Residual Current Device – RCD (also known as
an Earth Leakage Circuit Breaker – ELCB) with a
maximum rated residual current of 30mA.

Table of Contents

Questions and Answers

  • J
    Jamie BryanAug 8, 2025
    What to do if my onga JS100 does not start?
    • K
      Kristi RobertsAug 8, 2025
      If your Onga Water Pump isn't starting, ensure it's connected to a live outlet. Also, check the circuit breakers and fuses. If the pressure controller detects no water in the tank, make sure there's enough water and press the reset or start button. A blocked pump can also be the cause; disconnect it from the power and inspect the housing and discharge for any obstructions. If none of these steps work, the capacitor may be defective, and you should call a qualified service technician.
  • M
    megancooperAug 14, 2025
    Why does my onga JS100 Water Pump have poor performance with low pressure?
    • B
      Brianna SanchezAug 14, 2025
      To troubleshoot low pressure or flow in your Onga Water Pump, first, check the suction line for leaks, especially at the joints. If the tank water level is too far below the pump, consider discussing a better pump option with your Onga dealer or moving the pump closer to the tank. Also, a worn or damaged pump can cause poor performance, so ask your Onga dealer to investigate worn parts.
  • W
    William DavisAug 19, 2025
    What to do if there is no water from onga JS100?
    • M
      Melissa VillegasAug 19, 2025
      If your Onga Water Pump isn't providing water, first ensure the pump body and suction line are filled with water before starting. Check the suction line for leaks, particularly at the joints. Blockages in the pump or discharge can also prevent water flow, so disconnect the pump from power and inspect for foreign matter. Make sure all valves on the tank, pump, and outlets are open. If the tank doesn't have enough water, wait until it refills and then press the reset or start button on the pressure controller. Also, check and clean the pump if it's not producing enough pressure, and inspect/clean any in-line or tap filters that may be blocked. Finally, check system pressure and adjust the pressure switch accordingly.
  • J
    Jennifer MartinezAug 26, 2025
    Why does my onga JS100 run intermittently?
    • C
      Charles Williams IIIAug 27, 2025
      If your Onga Water Pump runs intermittently, start by checking for small leaks in your household plumbing and fix them. Ensure that the water temperature remains within the specified limits. Verify that the voltage is within the allowable limits as stated in the specifications, and correct if necessary. Also, make sure there's adequate ventilation for the motor cooling fan.
  • C
    carlsonjessicaSep 1, 2025
    What to do if onga JS100 Water Pump will not stop?
    • A
      Ann JacksonSep 1, 2025
      If your Onga Water Pump won't stop, even with no taps open, debris might be caught in the pressure controller; take it to your Onga dealer for service. Also, check for leaks in the household plumbing and fix them.

Summary

Model Data

Application

Installation

Preparation for Installation

Steps before installing the pump, including damage checks and leak prevention.

Pump Protection

Guidance on protecting the pump from environmental factors and ensuring warranty validity.

Pipe Installation

Instructions on connecting pipes, supporting them, and using appropriate fittings and seals.

Locating the Pump

Recommendations for placing the pump close to the water source on a stable footing.

Power Source

Advice on installing an appropriate electrical outlet for the pump.

Suction

Critical guidance on suction pipe setup for optimal performance and longevity.

Discharge

Information on discharge pipe sizing and pressure ratings for pump operation.

Pump Priming

Detailed steps for filling the pump and suction line with water before operation.

Electrical Installation

Instructions for safe and correct electrical connection, including RCD recommendations.

Operation

Start-up; Operation

Steps for starting the pump, including priming and system pressurization.

Pressure Switch

Details on the pressure switch, its settings, and adjustments for domestic use.

Aqua Packs

Information on charging Aqua Packs with air pressure before installation.

Aqua Pack Tank Recharge Procedure

Guide on checking and recharging the air pressure in Aqua Pack tanks annually.

Service and Maintenance

General Care and Maintenance

Advice on basic cleaning, storage, and periodic checks for pump wear.

Troubleshooting

Pentair Water Product Warranty

Terms and Conditions Applicable Internationally

Explains international warranty coverage, duration, and exclusions.

Terms and Conditions Applicable in Australia and New Zealand

Details local warranty coverage, duration, and what is excluded.

Spare Parts

Information on the availability and stocking of spare parts after production.

How to Get Service

Instructions on how to claim warranty service, including required information and procedures.

Limitation of Implied Warranties

States that express warranties supersede implied ones like merchantability.

Exclusion of Damages

Lists damages Pentair Water is not liable for, such as consequential or incidental losses.

Effective Law

Outlines the governing laws and consumer rights specific to Australia and New Zealand.

onga JS100 Specifications

General IconGeneral
Brandonga
ModelJS100
CategoryWater Pump
LanguageEnglish

Related product manuals