EasyManua.ls Logo

Onicon system-10 - Page 34

Onicon system-10
67 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • sales@onicon.com
System-10-P1 Manual 09/15 - 0656-11 / 18320 Page 34
P1 POINTS
Pt Name/Range Type Category COV OVR Default Initial Current
1 Address Range: 1-99 02 LAO NO YES 99 11
H
None
2 Application 02 LAO NO NO 1999
10
1999
10
None
3 Energy Rate - 0-32,767 03 LAI YES NO 0 0 Integer
4 Flow Rate - 0-32,767 03 LAI YES NO 0 0 Integer
5 Supply Temperature - 0-250°F 03 LAI YES NO 0 0 Integer
6 Return Temperature - 0-250°F 03 LAI YES NO 0 0 Integer
7 Delta Temperature - 0-250°F 03 LAI YES NO 0 0 Integer
8 Operating Mode: 1/Heat, 2/Cool 03 LDI NO NO 0 0 Byte
9 W0-M1 Energy: 000,000-009,999 03 LAI NO NO 0 0 Integer
10 W1-M1 Energy: 010,000-999,999 03 LAI NO NO 0 0 Integer
11 W0-M1Volume: 000,000-009,999 03 LAI NO NO 0 0 Integer
12 W1-M1 Volume: 010,000-999,999 03 LAI NO NO 0 0 Integer
13 W0-M2 Energy: 000,000-009,999 03 LAI NO NO 0 0 Integer
14 W1-M2 Energy: 010,000-999,999 03 LAI NO NO 0 0 Integer
15 W0-M2 Volume: 000,000-009,999 03 LAI NO NO 0 0 Integer
16 W1-M2 Volume: 010,000-999,999 03 LAI NO NO 0 0 Integer
17 W0-AuxiIn-1: 000,000-009,999 (Di3) 03 LAI NO NO 0 0 Integer
18 W1-AuxiIn-2: 010,000-999,999 (Di3) 03 LAI NO NO 0 0 Integer
19 Not Used
20 Point 20, Override Time (Hours)
Range 0-FF
02 LAO NO YES 1 1 None
21 M-1 E Reset - 0/Off, 1/Reset 01 LDO NO YES 0 0 Byte
22 M-1 V Reset - 0/Off, 1/Reset 01 LDO NO YES 0 0 Byte
23 M-2 E Reset - 0/Off, 1/Reset 01 LDO NO YES 0 0 Byte
24 M-2 V Reset - 0/Off, 1/Reset 01 LDO NO YES 0 0 Byte
25 AuxIn Reset - 0/Off, 1/Reset (Di3) 01 LDO NO YES 0 0 Byte
29 DAY.NGT
ON=Night; OFF=Day; Default=OFF
01 LDO NO YES 0 0 Byte
99 ERROR STATUS Bit Oriented 01 LAO NO YES 0 0 Integer
100 Point 100
Factory Flag
Factory Flag is not a point in the sense that the others are. It is referenced only by
the Memorize Point Command. Other commands should NAK it with “POINT DOES
NOT EXIST”.
NOTE: Also refer to the Siemens’ Application Note, Document No. 140-0280 for additional information.

Related product manuals