Onkyo TA-6510 User Manual

Useful Recording Functions
TAPE MONITOR @ AUTO SPACE
Tape Monitor indicator bm PLAY
OAUTO
SPACE
»
The
auto
space
function
is
useful
for
mut-
r- OPERATION — —— REPEAT ——~
N 4 ~ ing unwanted sections or inserting silent
REC]
(OFF
~
sections
between
selections
while
record-
LEVEL(B)
-co
-20-16
10
ing
or
when
in
the
rec/pause
mode.
TM
@
Press
the
AUTO
SPACE
button
at
any
=. point during a recording , or when the
CRIGHT
CH]
UOUORTIETCUOUEEEUET
:
unit
is
in
the
rec/pause
mode,
if
you
want to enter a blank section about five
seconds long.
e The ® indicator flashes on and off.
_ © After the blank section has been in-
serted, tape transport stops automati-
LEVEL(dB) -co 20-16-10 . cally, the deck returns to the rec/pause
SQ
Peewee
eee
eee
=
standby
mode
and
the
REC
and
ig
in-
| dicators turn on.
Daunbeaaneteenrensere - @ To continue recording, press
| the ® play button.
e The AUTO SPACE button works in
oe both the record and rec/pause modes.
-. @ To Insert a Blank Section of Tape
rt OPERATION = —=-— REPEAT —~——X
REC: Wf
Less Than Five Seconds Long
OPERATION
+
——
AEPEAT
—
:
Press
the
#8
PAUSE
button
to
return
to
me
PLAY
:
the
rec/pause
standby
mode
or
press
me m OF i the » button before the five second
LEVEL(dB)
-co
20-16
+10
|
period
has
elapsed.
|
[LEFT
CH
]
jane
engedeuingueuuiiil
~
To
Insert
a
Blank
Section
of
Tape
; More Than Five Seconds Long
—eeeeee : Hold the AUTO SPACE button down
for as long as you want the blank sec-
tion to be. The deck will return to the
rec/pause standby mode immediately
when the button is released.
_ This deck is a three-head deck, so by
A
_
switching
between
the
SOURCE
and
OSsource
_
TAPE
settings
you
can
compare
the
signal
4
S
_
which
has
just
been
recorded
on
the
tape
O
wre
-
with
the
source
signal.
TAPE
MONITOR
-
@
Listening
to
the
Original
Source
: Signal
Press the MONITOR button so that the
SOURCE indicator Lights.
When the SOURCE indicator is lit the
; signal from the LINE IN jacks is output.
- Listening to the Signal Just Re-
!
O
source
:
corded
on
the
Tape
NY
:
Press
the
MONITOR
button
so
that
the
Jor
|
TAPE
indicator
lights.
TAPE
MONITOR
When
the
TAPE
indicator
is
lit
the
just-
=_—) | recorded signal from the tape is output.
MPxX Filter for Recording FM Broadcasts
When
recording
FM
broadcasts
using
Dolby
NR,
the
19kHz
pilot
signal
and
the
38kHz
subcarrier
si
gnal
included
in
the
FM
broadcast
signal
can
cause
the
Dolby
circuitry
to
malfunction.
This
deck
isequipped
with
an
MPX
FILTER
button
to
prevent
this
from
occurring.
Press
the
MPX
FILTER
button
to
turn
on
the
MPX
filter.
The
[MPX
FILTER]
indicator
lights.
The
MPX
FILTER
button
should
be
ON
when
recording
FM
broadcasts
using
Dolby
NR
and
OFF
at
all
other
times.
12

Onkyo TA-6510 Specifications

Power

power supply rating (UK and Australian models)	AC 240 V 50 Hz
power supply rating (European models except UK)	AC 230 V, 50Hz
power supply rating (Worldwide models)	AC 120 and 220 V, Switchable 50/60 Hz
power consumption	13 watts

Audio Specifications

frequency response (normal)	20–18, 000 Hz
frequency response (high)	20–19, 000 Hz
frequency response (metal)	20–20, 000 Hz
signal-to-noise ratio	60 dB (metal tape, Dolby NR off)

Input and Output

input sensitivity	80 mV
input impedance	50 kohms
standard output level	500 mV
optimum load impedance (output)	over 50 kohms
optimum load impedance (headphone jack)	8 to 200 ohms

Weight and Dimensions

weight	5.0 kg
dimensions	455(W) x 120(H) x 310(D) mm