TX-NR929/ DTR-60.5/ DHC-60.5
OPERATION CHECK-7
4.TEST MODE
4-2.
TEST MODE FOR OPERATION
a.
Push STANDBY/ON button while pushing down TV/CD button to display "T
EST-__".
b.
Next, if the following keys are pushed, it becomes a each TEST MODE.
TEST MODE
1-00 2-00 3-00 4-00 5-00 6-00 KEY TEST
FIRMWARE
VERSION
BD/DVD CBL/SAT STB/DVR
GAME
GAME1
TUNER TV/CD
MEMORY
(Re-EQ)
TONE
TEST MODE
c.
In the test mode, (TONE)- button is TEST MODE DOWN and (TONE)+ button is TEST MODE UP.
d.
The unit receives the following remote control signals, the set will be the test mode or be changed the step No.
D22F K113(D0) ---
Got out of the test mode.
D22F K114(D1) ---
Got the"TEST 1-00".
D22F K115(D2) ---
Got the"TEST 2-00".
D22F K116(D3) ---
Got the"TEST 2-00".
D22F K117(D4) ---
Got the"TEST 4-00".
D22F K112(CF) ---
Got the"TEST 5-00".
D22F K111(CE) ---
Got the"TEST 6-00".
D22F K118(D5) ---
Made the 1st position of a figure of the step No. "1", and call the setting.
D22F K119(D6) ---
Made the 1st position of a figure of the step No. "2", and call the setting.
D22F K120(D7) ---
Made the 1st position of a figure of the step No. "3", and call the setting.
D22F K121(D8) ---
Made the 1st position of a figure of the step No. "4", and call the setting.
D22F K122(D9) ---
Made the 1st position of a figure of the step No. "5", and call the setting.
D22F K123(DA) ---
Made the 1st position of a figure of the step No. "6", and call the setting.
D22F K124(DB) ---
Made the 1st position of a figure of the step No. "7", and call the setting.
D22F K125(DC) ---
Made the 1st position of a figure of the step No. "8", and call the setting.
D22F K126(DD) ---
Made the 1st position of a figure of the step No. "9", and call the setting.
D22F K127(DE) --
Made the 1st position of a figure of the step No. "0", and call the setting.
D22F K128(DF) ---
Made the 2st position of a figure of the step No. increment.
e.
"TEST 1-00" are used to check a protection circuit, and the relay recovered in one second.
f.
All test modes except for "TEST 3-00" are used to check an AF section.
g.
"TEST 3-00" is used to check an RF section, at this time the unit receives the following remote control signals,
they change the operation from really doing and they can made the operation
in tuner section.
D26DK26(19) --- TUNING UP
D26DK27(1A) --- TUNING DOWN
D26DK20(13) --- FM MUTE ON/OFF
h.
When the unit receives the following remote control signals, they can made the step No. up and down.
D26DK30(1D) --- STEP UP
D26DK31(1E) --- STEP DOWN
IDLING
TIMER FL TEST
FIRMWARE COMBINATION CHECK
ENTER
When the MPU version is displayed,
push "MEMORY(Re-EQ)"
CHECK SUM
TUNING MODE
(LATE NIGHT)
DIMMER
(RT/PTY/TP)
To Next Page
Loading...
