Onkyo TX-SR603X - Page 7

OPERATION CHECK-4
DSP DEBUG MODE
TX-SR603X
E1A48K015FF 23o
Ver. 1.00/05810a
<Ex.>
1 42 5 6 87 103 9
11
Check the operation of the circuit around DSP by the display in this mode.
This information helps to pursue the faulty point.
UNLOCK
E = UNLOCK
= LOCK
1
Digital Selecter
D = DIGITAL
A = ANALOG
1 = COAX1
2 = OOAX2
3 = OPT1
4 = OPT2
5 = OPT3
7 = FRONT
2
Sampling Frequency
96 = 96kHz
48 = 48kHz
44 = 44kHz
32 = 32kHz
-- = Not detect
3
AUTOBOOT DSP AB CODE
0 = FLASH
1 = ab_ac3_pl2
2 = ab_dts_pl2
3 = ab_neo6
4 = sgen_ab
5 = ab_pl2fs
6 = ab_dts_6dol
7 = ab_dts9624
8 = aac_pl2
6
Pre Emphasis
K = OFF
e = ON
4
DSP Detect Format
00 = Null
01 = Dolby Digital
03 = Pause
04 = MPEG1 L1
05 = MPEG1 L23/ MPEG2 w/o
06 = MPEG2 w/e
07 = MPEG2 AAC
08 = MPEG2 L1
09 = MPEG2 L2/3
9
DSP Decode
o = Decode OK x = Decode NG - = Analog in
10
To set in DSP debug mode
1. Press and hold down the DISPLAY button, then press the STANDBY/ON button when the unit is power ON.
" Ver. 1.00/05810a " is displays it only for 2 seconds.
2. Press the DISPLAY button, while the character of " Ver.1.00/05810a " is displayed.
To exit
Press STANDBY/ON button.
--------- DIR --------- ------ MEMORY/DOWNLOAD -----
DIR Status
0 = ANALOG
1 = PCM
2 = NOT_PCM
3 = DATA
4 = DTSCD
5 = MCH
6 = NOT DECIED
5
------------------------- DSP ----------------------------------------
Content of display
AUTOBOOT DSP C CODE
0 = ac_dts9624
1 = c_neo6
2 = c_oos_no_sd
3 = c_oos
4 = c_oob
5 = c_pl2
6 = c_pl2xthx
7 = c_thx
8 = c_spsetup
9 = version
7
DSP Status
00 = Power off
01 = Power on wait
10 = DSP reset
11 = DSP reset wait
12 = DSP AB boot ready
13 = DSP AB boot start
14 = DSP AB boot
15 = DSP C boot ready
16 = DSP C boot start
17 = DSP C boot
18 = DSP soft reset
20 = DSP C app start
8
21 = DSP C HW Config set
22 - 2A = DSP C SW Config set
3F = DSP C kick start
40 = DSP AB App start
41 = DSP AB HW Config set
42 - 4B = DSP AB SW Config set
AF = DSP ab kick start
0B = DTS1
0C = DTS2
0D = DTS3
1B = MPEG2 AAC1
1C = MPEG2 AAC2
20 = Silent
22 = DTS CD
23 = PCM
11
Mute Condition
0 = Mute off
1 = Input selector mute
2 = Parameter selector mute
3 = 1+2
4 = DSP mute
5 = 1+4
6 = 2+4
7 = 1+2+4
8 = DIR mute
9 = 1+8
A = 2+8
B = 1+2+8
C = 4+8
D = 1+4+8
E = 2+4+8
F = 1+2+4+8
------------------------- MUTE ----------------------------------------