What to do if OPTI-UPS DS2000B is on battery?
If your OPTI-UPS UPS is operating on battery power, it's crucial to save your data promptly and perform a controlled shutdown of your systems to prevent data loss or corruption.
Why is my OPTI-UPS DS2000B showing Output Overload?
The OPTI-UPS UPS is overloaded because the connected equipment needs more power than the UPS can supply in Line Mode. To resolve this, turn off the least important equipment. If this solves the problem, the UPS will switch from bypass back to normal operation.
What to do if my OPTI-UPS UPS displays an Over-Temperature warning?
If your OPTI-UPS UPS displays an Over-Temperature warning, ensure that the unit’s fans and vent holes are not blocked. Also, verify that the surrounding temperature is not above 40 degree C. If these steps don't solve the problem, contact your service representative.
What to do if OPTI-UPS DS2000B has a Bus Fault?
If your OPTI-UPS UPS has a Bus Fault (High internal DC bus Voltage), turn off the protected loads, turn off the UPS, and call your local dealer for assistance.
What to do if my OPTI-UPS UPS displays an Over-Charge error?
If your OPTI-UPS UPS displays an Over-Charge error, turn off the protected loads and turn off the UPS. Then, contact your local dealer for further assistance.
What does it mean when my OPTI-UPS DS2000B UPS says 'Site wiring Fault'?
A 'Site wiring Fault' on your OPTI-UPS UPS indicates voltage detected between Neutral and Ground. This could mean the UPS mains connector polarity is wrong; try rotating the connector (Schuko). It can also mean the UPS is installed to a mains supply without ground. See page 15 on how to disable the site wiring alarm.
What to do if OPTI-UPS UPS reports a Charger Failure?
If your OPTI-UPS UPS indicates a Charger Failure, you should contact your local dealer for support.
What to do if my OPTI-UPS DS2000B indicates a Battery Test?
No action needed. The OPTI-UPS UPS will return to normal operation when it successfully completes the battery test.
What to do if OPTI-UPS DS2000B reports Output Short?
If your OPTI-UPS UPS reports an Output Short, contact your local dealer for assistance.
What to do if OPTI-UPS UPS indicates High output Voltage?
If your OPTI-UPS UPS indicates High output Voltage, contact your local dealer for assistance.
Limits implied warranties and excludes specific types of damages.
Provides critical safety instructions for UPS operation and maintenance.
Covers safe handling, storage, and installation procedures.
Specifies the limited operations users are allowed to perform.
Specifies environmental concerns for safe installation and operation.
Provides instructions for connecting the UPS to mains and loads.
Lists audible alarms and their corresponding causes.
Provides common UPS issues, alarms, and recommended actions.
Step-by-step tutorial for replacing the UPS batteries.
Technical data for 1000-3000 VA models at 100/110/120V.
Technical data for 1000-3000 VA models at 220/230/240V.
Technical data for 19" rack-mount models at 100/110/120V.
Technical data for 19" rack-mount models at 220/230/240V.
Details specifications for 220/230/240V models.
Provides details on battery types, quantities, and backup times.
Details battery packs for 19" Rack-mount Model (2U).
General| Category | UPS |
|---|---|
| Capacity | 2000VA / 1200W |
| Output Power | 1200 W |
| Output Frequency | 50/60 Hz |
| Number of Batteries | 2 |
| Communication Ports | USB |
| Form Factor | Tower |
| Transfer Time | 4 ms |
| Battery Type | Sealed Lead Acid |
| Data Line Protection | RJ-45 |
| Weight | 12 kg |
To Next Page