Optimum OPTIdrill D17 Pro - Page 3

Version 1.0.3 - 2022-04-06 3Originalbetriebsanleitung
D17 Pro│D23 Pro│D26 Pro│D33 Pro EN
D17Pro_D23Pro_D26Pro_D33Pro_DE_GBIVZ.fm
4.7 Drehzahlveränderung...................................................................................................................................39
4.7.1 Drehzahltabellen.............................................................................................................................39
4.7.2 Drehzahlanzeige.............................................................................................................................42
4.8 Vor dem Arbeitsgang....................................................................................................................................42
4.9 Während dem Arbeitsgang...........................................................................................................................42
4.10 Pinolenvorschub...........................................................................................................................................42
4.11 Ausbau, Einbau von Bohrfuttern und Bohrern..............................................................................................43
4.12 Schnellspann - Bohrfutter.............................................................................................................................43
4.12.1 Einbau Bohrfutter............................................................................................................................43
4.13 Kühlung ........................................................................................................................................................44
5 Ermitteln der Schnittgeschwindigkeit und der Drehzahl
5.1 Tabelle Schnittgeschwindigkeiten/ Vorschub ...............................................................................................45
5.2 Drehzahltabelle ............................................................................................................................................45
5.2.1 Beispiel zur rechnerischen Ermittlung der erforderlichen Drehzahl an Ihrer Bohrmaschine ..........47
6 Instandhaltung
6.1 Sicherheit .....................................................................................................................................................48
6.1.1 Vorbereitung ...................................................................................................................................48
6.1.2 Wiederinbetriebnahme....................................................................................................................49
6.2 Inspektion und Wartung ...............................................................................................................................49
6.3 Instandsetzung.............................................................................................................................................53
6.3.1 Kundendiensttechniker ...................................................................................................................53
7 Störungen
8Anhang
8.1 Urheberrecht ................................................................................................................................................56
8.2 Terminologie/Glossar ...................................................................................................................................56
8.3 Mangelhaftungsansprüche / Garantie ..........................................................................................................56
8.4 Lagerung ......................................................................................................................................................57
8.5 Entsorgungshinweis / Wiederverwertungsmöglichkeiten: ............................................................................58
8.5.1 Außer Betrieb nehmen....................................................................................................................58
8.5.2 Entsorgung der Neugeräte-Verpackung.........................................................................................58
8.5.3 Entsorgung des Altgerätes .............................................................................................................58
8.5.4 Entsorgung der elektrischen und elektronischen Komponenten ....................................................59
8.6 Entsorgung über kommunale Sammelstellen...............................................................................................59
8.7 Änderungsinformationen Betriebsanleitung .................................................................................................59
8.8 Produktbeobachtung ....................................................................................................................................59
1Safety
1.1 Rating plates ................................................................................................................................................62
1.2 Safety instructions (warning notes) ..............................................................................................................63
1.2.1 Classification of hazards.................................................................................................................63
1.2.2 Other pictograms ............................................................................................................................64
1.3 Intended use.................................................................................................................................................65
1.4 Reasonably foreseeable misuse ..................................................................................................................65
1.4.1 Avoiding misuse..............................................................................................................................65
1.5 Possible dangers caused by the drilling machine ........................................................................................66
1.6 Qualification..................................................................................................................................................67
1.6.1 Private Users ..................................................................................................................................67
1.6.2 Obligations of the User ...................................................................................................................67
1.6.3 Craftsman or industrial use.............................................................................................................67
1.7 User positions...............................................................................................................................................68
1.8 Safety measures during operation ...............................................................................................................68
1.9 Safety devices..............................................................................................................................................68
1.10 Safety check.................................................................................................................................................69
1.11 Emergency stop button ................................................................................................................................70
1.12 Drill chuck guard...........................................................................................................................................70
1.13 Protective cover of V-belt. ............................................................................................................................70
1.14 Personal protective equipment.....................................................................................................................71