Oriental motor AZ Series User Manual (English)

Other manuals for Oriental motor AZ Series

Operating Manual60 pages

User Guide56 pages

Questions and Answers:

D
Diane CoffeyAug 15, 2025
What to do if Oriental motor AZ does not operate?
- J
  Jenna McguireAug 15, 2025
  If your Oriental motor Controller does not operate, there are several potential causes: * If you are using an electromagnetic brake motor, check the connections between the electromagnetic brake and the driver. * Ensure the STOP input is OFF. * Verify the position (distance) is set correctly in the operation data for positioning operations. * In JOG operation, ensure that the FW-JOG and RV-JOG inputs are not simultaneously ON. If they are, turn them both OFF, then turn only one of them ON.
T
Tammy JordanAug 18, 2025
Why is my Oriental motor AZ operation unstable?
- S
  Sarah RodriguezAug 18, 2025
  Unstable operation of your Oriental motor Controller can be due to: * A connection error in the motor or power supply. Check the connections between the driver, motor, and main power supply. * The base current rate setting being too low. Check the setting of the 'Base current' parameter. If the current is too low, the motor torque will also be too low, and operation will be unstable.
K
Kelly MurphyAug 22, 2025
What to do if Oriental motor AZ vibration is too great?
- D
  David JosephAug 22, 2025
  Excessive vibration in your Oriental motor Controller may be due to the load being too small. Try lowering the current using the 'Base current' parameter. Vibration will increase if the motor’s output torque is too large for the load.
S
Samantha SandersAug 26, 2025
How to fix an Oriental motor Controller that rotates in the opposite direction?
- H
  hcarpenterAug 26, 2025
  If your Oriental motor Controller rotates in the direction opposite to what you specified, check the setting of the 'Motor rotation direction' parameter and correct it as needed.
C
Cynthia DuffyAug 28, 2025
What to do if the electromagnetic brake does not release on my Oriental motor AZ?
- J
  James TravisAug 28, 2025
  If the electromagnetic brake on your Oriental motor Controller fails to release, check the connection of the electromagnetic brake to ensure the main power supply is being supplied to it.
P
Pamela ButlerAug 31, 2025
What to do if Oriental motor AZ is not excited?
- K
  Kristi SpenceAug 31, 2025
  If your Oriental motor Controller is not excited, check the connections between the driver and motor. Also, ensure that the FREE input is OFF. If it is ON, turn it OFF.
R
Robert BarberSep 4, 2025
What to do if Oriental motor AZ Controller does not rotate although the READY LED is lit?
- J
  Joseph TurnerSep 4, 2025
  If your Oriental motor Controller's READY LED is lit but the motor doesn't rotate, ensure signals are wired correctly. Check for disconnected signal lines and verify that the correct signal is input. Avoid inputting multiple signals simultaneously.
T
Toni HicksSep 7, 2025
Why does Oriental motor Controller have holding torque in non-excitation state?
- G
  gdunlapSep 7, 2025
  The holding torque in a non-excitation state of your Oriental motor Controller is an effect of the dynamic brake. To release the dynamic brake, shut off the main power supply or turn the FREE input ON.
N
Nicole CannonSep 12, 2025
Why does the gear output shaft rotate opposite to the Oriental motor Controller?
- M
  Mrs. Kristina GriffinSep 12, 2025
  If the gear output shaft of your Oriental motor Controller rotates in the opposite direction to the motor, it may be because: with TS geared type, the gear output shaft rotates in the direction opposite to the motor when the gear ratio is 20 or 30; With Harmonic geared type, the gear output shaft always rotates in the direction opposite to the motor.

Oriental motor AZ Series Specifications

General

Control Modes	Position, Speed, Torque
Number of Axes	1
I/O	Digital Inputs, Digital Outputs, Analog Inputs
Power Consumption	Varies by model
Protection Functions	Overcurrent, overvoltage, undervoltage, overload, overheat
Operating Temperature	0°C to 40°C (32°F to 104°F)
Humidity	85% RH or less (non-condensing)
Weight	Varies by model