EasyManua.ls Logo

Oriental motor BMUD60-C2 - User Manual

Oriental motor BMUD60-C2
44 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
HM-5187-4
Brushless Motor
BMU
Series
30 W /
60 W / 120 W
OPERATING MANUAL
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety precautions.
•
Please read it thoroughly to ensure safe operation.
•
Always keep the manual where it is readily available.

Table of Contents

Questions and Answers

  • J
    Jennifer MartinJul 25, 2025
    What to do if my Oriental motor Engine does not operate?
    • G
      Gregory RodriguezJul 25, 2025
      If your Oriental motor Engine does not operate, several factors could be the cause. First, check the connections between the driver and the power supply to ensure they are correctly connected. Second, verify that the operation switch is set to the "RUN" side, not "STAND-BY". If operating the motor using the operation switch, ensure the "external operation signal input" parameter is set to "OFF" after setting the operation switch to the STAND-BY side. When using external signals, the "external operation signal input" parameter should be set to "ON" or "RE" after turning the input operation signal OFF. Also, make sure either the FWD or REV input is ON, but not both. Finally, check for any alarms and reset after addressing the cause.
  • J
    Jared AdamsJul 29, 2025
    Why is my Oriental motor Engine rotating in the wrong direction?
    • A
      Andrea AcostaJul 30, 2025
      If your Oriental motor Engine rotates in the opposite direction to what you specified, there are a few potential causes. First, the FWD and REV inputs might be wrongly or not correctly connected; check these connections. Second, the gear ratio might be causing the gearhead output shaft to rotate in the opposite direction; consult the motor's operating manual for the gearhead output shaft's rotation direction. Also, check the rotation direction switch. Finally, if the rotation direction switch is set to REV, verify the setting of the "external operation signal input" parameter.
  • A
    alan79Aug 3, 2025
    What to do if the Oriental motor BMUD60-C2 operation is unstable or vibrating too much?
    • E
      Erica DouglasAug 3, 2025
      If the operation of your Oriental motor Engine is unstable, or if the motor vibration is too great, there are a couple of things you should check. First, make sure that the motor and gearhead output shaft are correctly aligned with the load shaft. Second, check for electrical noise by testing the operation with only the essential equipment (motor, driver, and any other external equipment required for operation). If noise is present, try moving the unit away from noise sources, reviewing the wiring, changing to shielded signal cables, or installing ferrite cores.
  • D
    David MarshAug 7, 2025
    What to do if I cannot perform settings using the dial on my Oriental motor Engine?
    • T
      Tiffany FrostAug 7, 2025
      If the setting cannot be performed using the setting dial of your Oriental motor Engine, the lock function might be enabled. You should release the lock function.
  • T
    Troy SanchezAug 11, 2025
    Why is the set rotation speed not saved on my Oriental motor BMUD60-C2 Engine?
    • E
      Edwin JohnsonAug 11, 2025
      If the set rotation speed is not being saved on your Oriental motor Engine, ensure that you are confirming the speed by pressing the setting dial after you set it.
  • C
    clarkejuanAug 15, 2025
    Why is the rotation speed not displayed on my Oriental motor BMUD60-C2?
    • M
      Mr. Albert SchmittAug 15, 2025
      If the rotation speed is not displayed on your Oriental motor Engine, the "panel initial view" parameter might not be set to show the rotation speed. Set the "panel initial view" parameter to the rotation speed.
  • K
    Kimberly MurphyAug 20, 2025
    Why is my Oriental motor BMUD60-C2 not reversing with the rotation direction switch?
    • E
      evanselizabethAug 20, 2025
      If your Oriental motor Engine is not reversed by the rotation direction switch, check the setting of the "external operation signal input" parameter. It may be set to "RE."

Summary

Safety Precautions

General and Core Safety

Covers general handling, operation, maintenance, and repair safety guidelines.

Installation and Connection Safety

Safety aspects for installing and connecting the motor and driver.

Warning Labels and Cautions

Details regarding warning labels and specific cautions.

Precautions for Use

Usage Guidelines and Restrictions

Covers output matching, prohibited operations, and environmental considerations.

Connection and Handling Safety

Safety for connecting, handling semiconductors, and data saving.

Preparation

Product Verification and Model Identification

Checking included items and identifying product models.

Component Overview and Compatibility

Describes product parts and lists compatible combinations.

Installation

Installation Location Requirements

Specifies ideal environmental and site conditions for driver installation.

Driver Mounting and Orientation

Details driver installation methods and mounting direction.

Connection

Motor and Driver Wiring

Procedures for connector and cable types, including detachment.

Grounding and Power Connections

Grounding methods and power supply connection.

I;O Signal Wiring and Diagrams

Connecting I/O signals and related diagrams.

Operating

Operation Mode Overview

Explains front panel vs. controller operation.

Front Panel Operation

Connecting and operating via the front panel.

External Controller Operation

Operating via controller, parameter settings, and rotation direction.

Multi-Speed Operation Setup

Configuring and operating with multiple speeds.

Convenient Functions

Functionality Overview

Lists available functions and their descriptions.

Parameter and I;O Signal Reference

Detailed list of parameters and I/O signals.

Operation Settings and Controls

Setting operation data, acceleration/deceleration time, and speed limits.

Data Locking and Load Holding

Locking settings and using load holding torque.

Alarms and Warnings

Alarm Overview and Reset Methods

Information about alarms, list, and how to reset.

Warning Information and Records

Details on warning types, conditions, and records.

Troubleshooting and Remedial Actions

Common Operation and Setting Issues

Addresses common problems like motor not operating, incorrect rotation, or setting issues.

Stability and Vibration Troubleshooting

Issues related to unstable operation and excessive vibration.

Maintenance and Inspection

Periodic Inspection Guidelines

Recommendations for inspecting the motor and driver.

Warranty and Disposal Information

Details on product warranty and proper disposal.

Accessories (Sold Separately)

Cabling Accessories

Power supply and connection cables for extending wiring.

Mounting and Protection Accessories

Mounting brackets, covers, and enclosure boxes.

Reference

Compliance Standards and Markings

Details UL, CSA, CE, EMC, and RoHS compliance.

EMC Directive Installation and Wiring

Methods for EMC compliance, including filters, grounding, and wiring.

Product Specifications and Pin Assignments

Technical specs, pin configurations, and general specifications.

Oriental motor BMUD60-C2 Specifications

General IconGeneral
BrandOriental motor
ModelBMUD60-C2
CategoryEngine
LanguageEnglish

Related product manuals