To Next PageTo Next Page
Need help?Do you have a question about the Oval ALTI mass CA080 and is the answer not in the manual?
General| Brand | Oval |
|---|---|
| Model | ALTI mass CA080 |
| Category | Measuring Instruments |
| Language | English |
Detailed technical specifications for sensor units, covering materials, connections, and operating limits.
General specifications for the transmitter, covering power, communication, outputs, and standards compliance.
Performance data for Type S with stainless steel tubes, including flow rate and accuracy.
Performance characteristics for Type B models, including flow rate, accuracy, and density measurements.
Technical specifications for Type U sensor units, including materials, connections, and operating limits.
Performance data for Type S with stainless steel tubes, including flow rate and accuracy.
Technical specifications for Type S sensor units, detailing material, connections, and performance parameters.
Performance characteristics, including accuracy and repeatability for Type U models.
Performance data for Type S with titanium tubes, covering flow rate and accuracy specifications.
Technical specifications for Type B sensor units, including materials, connections, and performance data.
Part names and outline dimensions for Type U sensor units.
Outline dimensions for ferrule fitting sensor units, including integrated and separate types.
Outline dimensions and weights for separately mounted CA00A, CA001, and CA003 sensor units.
Outline dimensions and weights for integrally mounted CA100 to CA250 sensor units.
Outline dimensions and weights for separately mounted CA006 to CA080 sensor units.
Outline dimensions and weights for separately mounted CA100 to CA250 sensor units.
Outline dimensions and weights for integrally mounted CA006 to CA080 sensor units.
Outline dimensions for low temp. explosionproof sensor units with ferrule fittings, showing size and weight.
Outline dimensions and weights for Type S stainless steel tube sensor units.
Outline dimensions and weights for Type S titanium tube sensor units.
Outline dimensions for Type S ferrule fitting sensor units, including integrated and separate types.
Outline dimensions for separately mounted sensor units with ferrule fittings, specifying size, weight, and connections.
Outline dimensions and weights for integrally mounted Type S titanium tube sensor units.
Part names and outline dimensions for Type B sensor units.
Outline dimensions for integrally mounted sensor units with ferrule fittings, including size and weight.
Outline dimensions and weights for separately mounted Type S titanium tube sensor units.
Outline dimensions and weights for Type B, integrally mounted sensor units, with various process connections.
Outline dimensions and weights for Type B, separately mounted sensor units, showing size and weight.
General guidelines for installing the flowmeter, focusing on flange type connections.
Guidelines for installing flange-type sensors, focusing on alignment, gaskets, and bolt tightening.
Instructions for installing screw-in type sensors for CA00A and CA001 models.
Procedures for installing sanitary fitting types, including welding companion sleeves and using clamps.
Procedure for sandwiching an O-ring and tightening for CA003 to CA015 screw-in types.
Instructions for installing screw-in type sensors for CA00A and CA001 models.
Details on making power and output signal connections to the transmitter housing terminals.
Details on making power and output signal connections to the transmitter housing terminals.
Wiring diagram showing connections for transmitter power and output signals.
Instructions for connecting the separately mounted sensor unit to the transmitter using the terminal block.
Wiring diagram showing connections for transmitter power and output signals.
Wiring diagram illustrating the connection between the separately mounted sensor unit and transmitter.
Procedure for checking the probe circuitry for faults, with corrective actions for detected issues.
Diagnostic test to verify the integrity of the drive coil and sensor connections.
Diagnostic test to identify problems within the transmitter, covering various internal components and conditions.
Procedure for performing zeroing using the LCD switches to correct offset drift and ensure accurate measurements.
Automatic zeroing initiated by a status input signal to minimize offset flowrate drift.
A table listing error types, descriptions, coping actions, and influences on output for troubleshooting.
Details on explosionproof specifications, including TIIS, ATEX, IECEx, CSA, EAC, and NEPSI standards.
Details on TIIS explosionproof specifications for integral and separate type converters and detectors.
ATEX and IECEx explosionproof specifications for converters and detectors, covering applicable standards and type symbols.
CSA explosionproof requirements for converters and detectors, including applicable standards and adapter specifications.
EAC explosionproof specifications for converters and detectors, detailing applicable standards and model code explanations.
NEPSI explosionproof specifications for converters and detectors, including applicable standards and model code explanations.
ITRI explosionproof specifications for converters and detectors, covering applicable standards and model code explanations.
Explanation of product code structure for Type U models, including model selector charts.
Explanation of product code structure for Type S models, including tube types.
Explanation of product code structure for Type S stainless steel tube models.
Explanation of the main product code structure for Type U models CA00A to CA080.
Explanation of the main product code structure for Type B models, detailing size, materials, and connections.
Explanation of the main product code structure for Type U models CA100 to CA250.
