AFTER-USE | CARE & MAINTENANCE XS1 USER MANUAL
17
PREPARING THE XS1 FOR
INACTIVITY
POWERING DOWN THE XS1
After completing your workouts, view your progress
and activity on the XS1.
home screen.
Under the Progress section, view a summary of the
current week’s workouts. The data in the Muscle
Balance rail and the Activities rail accounts for your
overall progress on the XS1. The Milestones rail shows
your overall progress in gray and your current week’s
progress in green.
The Activity section displays a general overview of
your previously performed workouts.
For your safety and the longevity of your device, re-
move all accessories and the bench from the XS1
when the device is not in use.
When an accessory remains attached to the device,
the system may detect false activity by mistaking the
weight of the accessory as force applied by you. Any
false activity will force the idle mode to quit prema-
turely, causing the cable motors to restart.
The power switch is located at the back of the device.
After your workout, there is no need to power down
your device because the XS1 is designed to go into
sleep mode, protecting the system while remaining
available for software upgrades.
Only shut down your XS1 in the event in which you
need to power cycle the device for troubleshooting
purposes.
Turn the power switch to the OFF position to power
down the XS1.
CAUTION: DO NOT rapidly shut down and power on
your device. Wait at least two minutes before power-
ing your device back on after shutting down.
VIEW PROGRESS & ACTIVITY
CLEANING
SOFTWARE MAINTENANCE
Keeping your XS1 unit clean is essential for ensur-
ing proper operating conditions of your equipment.
Proper care and cleaning will extend the life of your
equipment and reduce premature aging and wear.
CAUTION: Always shut down and unplug the XS1 be-
fore cleaning.
• Accessories should be wiped down after use
and cleaned daily with a mild soap and water
mix or an approved antibacterial cleaner.
• The padded upholstery of the strength and
multifunction bench should be cleaned after
each use with a mild soap and water mix or a
non-abrasive, gentle antibacterial cleaner.
• The main frame of the device should be
cleaned weekly with a mild soap and water
mix and damp cloth or a gentle antibacterial
cleaner to remove all dust and accumulated
contaminants.
• Gently wipe the touchscreen with a clean, soft,
and dry cloth.
CAUTION: DO NOT use cleaners that contain solvents,
alcohol, or abrasives.
When an update is ready to be installed on your de-
vice, the XS1 will notify you.
Ensure your device is connected to the internet for
all software updates. Tap Update Now for all required
updates or you may select Skip to install optional up-
dates later. Tap the blue looping arrow in the top right
corner of the screen to install skipped updates.
You can view the current software version of your
XS1 by navigating to the drop-down menu in the top
right corner, selecting Settings, followed by About
your XS1.
PREVENTATIVE MAINTENANCE
Preventative maintenance is crucial to maintaining this
equipment’s functionality and safety. Visual inspections
of your XS1 unit will ensure a safe environment and
promote awareness of any potential issues that may re-
quire maintenance prior to equipment failure. Contact
OxeFit Support immediately for replacement parts.
CAUTION: DO NOT have opened beverages on or near
the XS1.
DAILY
• Verify that the slide handles can be raised and
lowered smoothly. As the handles move, listen for
unusual sounds. Report any abnormalities to sup-
port immediately.
• Inspect carabiners to verify that the latches are
working properly and are damaged-free.
WEEKLY
• Cables should be inspected for damage, includ-
ing fraying, abrasion, signs of wear, twisting, or
excessive rubbing on pulleys.
If you notice any signs of issues or abnormalities, dis-
continue use and contact OxeFit Support immediately.
MONTHLY
• Inspect all accessories for wear or damage, and
replace them as needed.
• Inspect upholstery for wear or damage, and re-
place them as needed.
• Inspect pulleys for integrity, cracking, or rubbing
caused by excessive wear. Any incidents of wear
should elicit immediate replacement of the dam-
aged pulley.
To Next Page
Loading...