Ozito ECS-355 - Description of Symbols; Hints & Tips; Spare Parts; Caring for the Environment

HINTS & TIPS
• Donotforcethesawintothecut.Applyonlylightpressurewhilstrunningthe
motoratfullspeed.
• Ifthesawchaingetscaughtinthecut,donottrytoremoveitbytwistingthe
guideorpullingforcibly.Usealeverorwedgetoopenupthecutsothatthe
saw chain is freed.
• Whilecutting,always:
– Runthechainsawmotoratfullspeed.Thismakesthejobsafer,asthere
islesschanceofpull-inorkick-back.
– Positionyourbodytotheleftofthechainsawsoifitkicksback
uncontrollably,itgoesoveryourrightshoulder,neverstandinthecutting
line of the saw.
– Keeparmgripwithyourlefthandonthefronthandle,withyourthumb
securely below the handle.
• Theswivelofyourwristinakick-backsituationwillactivatethechainbrake.
• Makesurethechainistensionedcorrectly.
Chain Sharpening
Chain File:3.96mm(5/32”)
Chain Pitch:9.53mm(3/8”)
Chain Gauge:1.3mm(0.050”)
Sharpenthechainregularlytomaintainoptimum
performanceofthesaw.Signsofadullchainare:
• Thesawdustbecomespowder-like
• Extra force is required to execute a cut
• Thecutdoesnottrackinastraightline
• Increased vibration
Sharpeneachcutterusingachainle.Alwaysuseoutwardstrokesand
maintaina30°anglebetweenthechainandle.Aftersharpening,thecutters
must all have the same width and length.
Afterevery3–4usesgetanauthorisedrepaircentretoprofessionallysharpen
yourchain.Theyhavethespecialtoolsnecessarytoensurethecorrectcutting
anglesanddepths.
Guide bar wear
Reverse the guide bar every 8 working hours to ensure uniform wear. Check
theguiderailsfrequentlyandifnecessaryremoveburrsandsquareuptherails
usingaatle.
Note: Thechainsawwarrantydoesnotcovercomponentsthathavebeen
subjectedtooperatorabuseornegligence.Toreceivefullvaluefromthe
warranty,theoperatormustmaintainthechainsawasinstructedinthismanual.
Ozito Industries will not be responsible for any damage or injuries
caused by repair of the tool by an unauthorised person or mishandling
or mistreatment of the tool. This tool is designed for Domestic Home Use
only. Use in commercial or industrial environments will void the warranty.
CARING FOR THE ENVIRONMENT
Toolsthatarenolongerusableshouldnotbedisposedofwith
household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council
authority for recycling advice.
Recyclingpackagingreducestheneedforlandllandraw
materials.Reuseofrecycledmaterialdecreasespollutioninthe
environment.Pleaserecyclepackagingwherefacilitiesexist.
Check with your local council authority for recycling advice.
Chain    SPECS355-62
GuideBar   SPECS355-61
BarSecuringNut   SPECS355-64
BarSecuringNutCover  SPECS355-65
CarbonBrush(Pair)  SPECS355-14
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito customer service
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: enquires@ozito.com.au
SPARE PARTS
DESCRIPTION OF SYMBOLS
Read instructions
Wear safety glasses
Beware of kickback
Regulator compliance mark
V Volts Hz Hertz
~ Alternating current W Watts
/min Revolutions or
reciprocation per minute
Double insulated
no No load speed
Warning
ø Diameter
Do not expose to rain
Wear muffs
Always hold the saw with
both hands
Disconnect and discontinue use should the power cord be damaged
outward
stroke
30°
WARNING!: WEAR HEAVY GLOVES WHEN
HANDLING THE CHAIN. HOLD THE GUIDE BAR
SECURELY IN A VICE.