29
Recording and Playback：P2 Cards
Recording and Playback
1 While pressing down the slide lock button, move the
slide-out door to the left.
The door opens.
2 Tilt down the EJECT button.
3 Then, depress the EJECT button to release the P2
card so that you can remove it.
Notes
z After insertion, do not remove the P2 card while it is
being accessed or recognized (the P2 card access LED
flashes orange), or the P2 card may fail. If your unit is not
set to turn on the P2 CARD ACCESS LED, before
removing the card ensure that pre-recording and/or
voice memo recording have finished (the P-REC
indication has stopped blinking and the V mark or VOICE
REC indication on the viewfinder screen has turned off)
after stopping recording or playback.
z If a P2 card being accessed is removed, the viewfinder
displays “TURN POWER OFF” and camera-recorder
gives a warning using an alarm and the WARNING LED.
In addition, all P2 CARD ACCESS LEDs blink rapidly in
green. If this is the case, turn the power off. For more
information on warning indications, see [Warning
System] (page 133).
z If a P2 card is removed while being accessed, clips on it
may become irregular. Check the clips and restore them
if required. For more information about how to restore
clips, see [Restoring Clips] (page 107).
z
If a P2 card being formatted is removed, it may be not be
formatted properly. In this case, the viewfinder displays
“TURN POWER OFF”. If this message appears, turn off the
power, then restart camera-recorder to reformat the card.
z If a P2 card is inserted while another P2 card is being
played back, the inserted P2 card is not recognised and
the P2 CARD ACCESS LED for that card does not come
on. Card recognition starts when the playback ends.
<For Your Information>
The P2 CARD ACCESS LEDs may be set to stay off using
the menu option ACCESS LED. This option can be found
on the <SYSTEM MODE> screen, which is accessible
from the SYSTEM SETTING page.
To prevent the content of a P2 card being accidentally
erased, position the write-protect switch on the P2 card at
[Protect].
Note
Write-protect switchover can be performed while the card
is being accessed (during recording or playback), but does
not take effect until access to the card ceases.
* The mode check indication is shown in the viewfinder. For more informa-
tion, see [Viewfinder Status Indication Layout] (page 62).
The access LED located on the display window blinks
when reading or writing data from or to any of the P2 cards
inserted in Slots 1 - 5 or stays illuminated when any of the
cards are recordable. It stays off when none of the P2
cards are recordable.
Removing P2 Cards
Depress the tilted-down
EJECT button to release
the P2 card.
Tilt down the EJECT
button.
To Prevent Accidental Erasure of P2 Card Content
P2 CARD ACCESS LED and status of P2 cards
P2 CARD
ACCESS LED
MODE CHECK
indication*
Status of P2 Card
Stays on in
green
ACTIVE Writing and reading
enabled
Stays on in
orange
ACTIVE Writing and reading
enabled. The card is
recordable (loop recording
also enabled).
Stays on in
orange or green
ACTIVE ! Writing and reading
enabled. However, some
clips recorded on the P2
card may not be able to be
read successfully.
Blinks in orange ACCESSING Writing or reading being
performed.
Blinks in green FULL The P2 card has no free
space. Only reading is
enabled.
PROTECTED The write-protect switch on
the P2 card is positioned at
[PROTECT]. Only reading
is enabled.
Stays off NOT
SUPPORTED
The card is not supported
by your unit. Replace the
card.
FORMAT ERROR The P2 card is not properly
formatted. Reformat the
card.
NO CARD No P2 card is inserted.
Protect
Write-protect switch
AJ-HPX2100E(English).book 29 ページ ２００６年１１月２７日 月曜日 午後４時３４分
To Next Page
Loading...
