Item Setting value Setting details
USER ASSIGN GAIN
M.GAMM
H.CHRM
U.CHRM
DRS
KNEE.S
UHD S.DTL
HD S.DTL
S.HUE
S.TONE
Sets the function to assign to [USER] of the [SELECT] dial.
The setting values represent the following functions.
GAIN : GAIN (operates the R, G, and B gain values simultaneously. This value will be
“0” when auto white balance adjustment is performed. The value will also be “0” when
the function assigned to USER ASSIGN has been changed to something besides
“GAIN”, or when switching to another camera.)
M.GAMM : MASTER GAMMA
H.CHRM : HD CHROMA GAIN
U.CHRM : UHD CHROMA GAIN
DRS: DRS
KNEE.S : KNEE SLOPE
UHD S.DTL : UHD SKIN DTL
HD S.DTL : HD SKIN DTL
S.HUE : SKIN CORRECTION(HUE)
S.TONE : SKIN CORRECTION(TONE)
IRIS LEV MODE ABS
RLTV
Selects between absolute values or relative values to be used for IRIS control oper-
ations.
ABS: Absolute value control.
RLTV: Relative value control.
CAM SEL CAM1 to CAM99 Switches between connected cameras.
DTL VOL UHD
HD
SD
Selects the target of detail control operations on the panel.
UHD: Control UHD detail.
HD: Control HD detail.
SD: Control SD detail.
SKIN DTL SW UHD
HD
SD
Selects the target of skin tone detail control operations on the panel.
UHD: Control UHD skin tone detail.
HD: Control HD skin tone detail.
SD: Control SD skin tone detail. (Enabled when [CONNECT SETTING] is set to “Serial
(AK)” or “LAN(AK)”.)
LCD BRIGHT 1 to 20 Sets the brightness of the LCD panel.
PANEL LED BRIGHT 1 to 5 Set the brightness of the panel buttons.
7SEG BRIGHT
GROUP1
0 to 15 Sets the brightness of the panel's 7-segment display (group 1).
This applies to the ND filter display, CC filter display, master gain display, and shutter
display.
7SEG BRIGHT
GROUP2
0 to 15 Sets the brightness of the panel's 7-segment display (group 2).
This applies to the iris display and camera selection number / master pedestal display.
BUZZER OFF
ON
Enable or disable the buzzer (beep/call tone).
PERIOD 0 to 5 [PERIOD] and [CYCLE] will be the time from which [CALL] was released for [CAMERA
CCU].
PERIOD: Flashing duration (sec).
CYCLE: Flashing cycle (For 1.0: 500 msec off → 500 msec lit (repeatedly)).
CYCLE 0.3
0.5
1.0
STD POSITION
M.GAIN
-6 to 0 to +36 Sets the standard position of the master gain (M.GAIN).
STD POSITION VAR -2.9 to 0.0 to +2.9 Sets the standard position of the master gain (M.GAIN) step value.
STD POSITION ND 1 to 2 to 5 Sets the standard position of the ND filter.
STD POSITION CC A to E Sets the standard position of the CC filter.
IRIS PRIORITY NON
Serial
LAN
Sets whether to prioritize iris control.
NON
Does not prioritize iris control.
If the camera's iris position does not match the ROP's [IRIS] lever position, match
the ROP's [IRIS] lever position to the camera's iris position.
Serial
If the camera's iris position does not match the ROP's [IRIS] lever position, the
ROP's [IRIS] lever position during serial connection will be the basis of operation.
LAN
If the camera's iris position does not match the ROP's [IRIS] lever position, the
ROP's [IRIS] lever position during IP connection will be the basis of operation.
When multiple ROPs are IP connected to a single camera and the [IRIS
PRIORITY] setting for each ROP is set to “LAN”, be aware that iris controls from
all of the ROPs will be performed directly.
- 112 -
ROP menu
To Next Page
Loading...
