– 57 –
Chapter 3 Preparation — Assigning function to the USER buttons
Assigning function to the USER buttons
Selected function can be assigned to the USER buttons.
f The buttons that can be used as a USER button are as follows.
- <USER 1> to <USER 9> buttons
These can be used as the USER buttons when the VIEW screen is displayed.
- Multidial (when <WB>/<USER>/<ISO/dB> switch is set to <USER>)
1
From the [SYSTEM SETTINGS] menu → [USER SWITCHES] → [USER1] to [USER9] or [USER TOGGLE], select the function to
assign to each.
r Functions assigned to the USER buttons in the factory setting
USER button Function
<USER 1> button [ONE PUSH AF]
<USER 2> button [PEAK./SQUARES F.A.]
<USER 3> button [SPOT METER]
<USER 4> button [E.I.S.]
<USER 5> button [WFM]
<USER 6> button [AWB]
<USER 7> button [SLOT SEL]
<USER 8> button [EXPAND]
<USER 9> button [OPEN IRIS F.A.]
Multidial [MONITOR VOL]
Functions assigned to USER buttons
Function assigned to <USER 1> to <USER 9> buttons
Item Description
[INHIBIT] Disables assignment of functions.
[AWB] Enables/disables the auto white balance.
[ONE PUSH AF] Assigns the one-push auto focus function.
[ONE PUSH A.IRIS] Assigns the one-push auto iris function.
[ATW LOCK] Fixes the value of the white balance. Pressing the USER button again will resume the operation of the auto
tracking white balance.
f Enable when the auto tracking white balance is operating.
[E.I.S.] Enables/disables the electronic image stabilization function.
[D.ZOOM] Enables/disables the digital zoom. It will zoom the angle of view 1.4 times both vertically and horizontally.
[IR SHOOTING] Enables/disables the IR recording.
[REC SW] Starts or stops the recording.
[PRE REC] Enables/disables the pre-recording.
[REC CHECK] Automatically plays back the last approximately three seconds of the previously shot clip.
[DEL LAST CLIP] Deletes the clip last shot.
[SLOT SEL] Selects the card slot with the SD card to record inserted.
Or, switches the card slot for the clip to display in the thumbnail screen.
[EXPAND] Enables/disables the enlarged display function (focus assist function).
[OPEN IRIS F.A.] Assigns the open iris focus assist function (focus assist function).
[PEAK./SQUARES F.A.] Enables/disables the peaking function and focus square display (focus assist function).
The display is selected in the [OUTPUT SETTINGS] menu → [LCD FOCUS ASSIST] → [PEAK./
SQUARES MODE].
[WFM] Switches the display of the waveform monitor. The waveform display is selected in the [OUTPUT
SETTINGS] menu → [LCD EI ASSIST] → [WFM MODE].
[SPOT METER] Displays/hides the spot meter.
This is enabled when the [OUTPUT SETTINGS] menu → [SDI/HDMI INDICATOR]/[LCD INDICATOR] →
[SPOT METER] → [ON] is set.
[ZEBRA] Displays/hides zebra patterns.
[LEVEL GAUGE] Displays/hides the level gauge.
[LEVEL GAUGE SET] Sets the current horizontal and vertical direction as the reference value of the level gauge.
[SDI COLOR] Switches the output image from the <SDI OUT> terminal.
[HDMI COLOR] Switches the output image from the <HDMI> terminal.
[LCD COLOR] Switches the output image from the <LCD> terminal.
[LCD CLEAN VIEW] Erases the display of the indicator or marker superimposed to the output video from the <LCD> terminal.
[LCD MARKER] Displays/hides the marker superimposed in the output video from the <LCD> terminal.
[COLOR BARS] Displays/hides the color bars.
[POWER LCD] Make it easier to view the LCD monitor in a well-lighted area such as outdoor.
To Next Page
Loading...
