Panasonic AW-UE100WP

Unicast port(Image) [1024 to 50000]
Enter the unicast port number (used when sending images from the
unit).
Only even numbers can be specified.
The port number cannot be set to 10670.
Factory settings:
H.264(1): 32004
H.264(2): 32014
H.264(3): 32024
H.264(4): 32034
Unicast port(Audio) [1024 to 50000]
Only even numbers can be specified.
The port number cannot be set to 10670.
Factory settings:
H.264(1): 33004
H.264(2): 33014
H.264(3): 33024
H.264(4): 33034
<NOTE>
• The unicast port number must be configured when [Transmission
type] is set to [Unicast port(MANUAL)].
Multicast address
[IPv4: 224.0.0.0 to 239.255.255.255
IPv6: Multicast address starting with FF]
Enter the multicast IP address.
Images and audio will be sent to the specified IP address.
Factory settings:
H.264(1): 239.192.0.20
H.264(2): 239.192.0.21
H.264(3): 239.192.0.22
H.264(4): 239.192.0.23
<NOTE>
• Verify usable multicast IP addresses before entering this setting.
• This setting does not work with the multicast address for link local
scope.
Multicast port [1024 to 50000]
Enter the multicast port number (used when sending images from the
unit).
Only even numbers can be specified.
The port number cannot be set to 10670.
Factory settings: 37004
<NOTE>
• When sending audio from the unit, a port number with “1000” added
to the multicast port number will be used.
Multicast TTL/HOPLimit [1 to 254]
Enter the TTL/HOPLimit value for multicast.
Factory settings: 16
<NOTE>
• When transmitting H.264 images via the Internet, transmitted
images may not appear depending on proxy server settings, firewall
settings, etc. In such cases, consult your network administrator.
• When displaying multicast images on a personal computer with
multiple LAN cards installed, disable the LAN cards that are not
used for reception.
z H.265
Set H.265 image settings.
The setting is confirmed with the [Set] button.
<NOTE>
• H.265 format images cannot be displayed in the live screen [Live] of
the unit.
• Use external devices and software compatible with H.265 images to
display H.265 images.
• When starting RTSP/RTP transmissions, set the following URLs for
the decoders and applications.
- For H.265(1):
rtsp://[unit’s IP address]/MediaInput/h265/stream_1
- For H.265(2)
rtsp://[unit’s IP address]/MediaInput/h265/stream_2
[/MediaInput/h265/stream_
*
] can be changed in [RTSP] of
[Advanced]. (→ page 147)
H.265 transmission [On, Off]
Whether to transmit the H.265 images is set here.
Factory settings: On
Image capture size [3840×2160, 1920×1080, 1270×720,
640×360]
Select the resolution for H.265 images.
Selectable options will vary depending on the selected resolution
setting.
H.265(1) 3840×2160, 1920×1080, 1270×720
H.265(2) 1920×1080, 1270×720, 640×360
Factory settings:
H.265(1): 1920×1080
H.265(2): 1280×720
<NOTE>
• [3840×2160] can be selected when the [Streaming mode] is
[H.265(UHD)].
114 115
Web screen configurations (continued)