Panasonic DP-MB310EU - Page 144

144
KX-MB2230EU/ KX-MB2270EU/ KX-MB2515EU/ KX-MB2545EU/ KX-MB2575EU/ DP-MB310EU
593 Time between CED and 300bps 1: 75msec
2: 500msec
3: 1sec
1~3 1 See How To Output The Journal Report (P.224)
and Receive Problem (P.218).
594 Overseas DIS detection select 1: detects at
the 1st time
2: detects at
the 2nd time
1, 2 1 See How To Output The Journal Report (P.224)
and Sometime There is a Transmit Problem
(P.217).
595 Receive error limit value set 1: 5%
2: 10%
3: 15%
4: 20%
1~4 2 If the number of errors during transmission exceeds
this value, the sending side terminates the call.
596 Transmit level set X dBm -15~00 10 Selects the FAX transmission level. Refer to Some-
time There is a Transmit Problem (P.217) and
Receive Problem (P.218).
598 Receiving sensitivity 43= -43dBm 20~48 48 Used when there is an error problem. Refer to How
To Output The Journal Report (P.224).
599 ECM frame size 1: 256
2: 64
1, 2 1 ----------
711 Dialing mode 1: PULSE
2: TONE
1,2 2
717 Transmit speed select 1: 14,400bps
2: 12,000bps
3: 9,600bps
4: 7,200bps
5: 4,800bps
6: 2,400bps
1~6 1 If the code 527 is set at 1, the code 717 and 718
work.
718 Receive speed select 1: 14,400bps
2: 12,000bps
3: 9,600bps
4: 7,200bps
5: 4,800bps
6: 2,400bps
1~6 1 If the code 527 is set at 1, the code 717 and 718
work.
721 Pause tone detect 1: ON
2: OFF
1, 2 2 Selects the tone detection for pause in dialing.
722 Redial tone detect 1: ON
2: OFF
1, 2 1 Sets the tone detection mode after redialing.
763 CNG detect time for friendly reception 1: 10sec
2: 20sec
3: 30sec
1~3 3 Selects the CNG detection tone of friendly recep-
tion.
774 Receiving T4 timer X 100msec 00~99 00 Use this function when delay occurs in the line and
communication.
(ex. Mobile comm) does not work well.
775 Transmission T4 timer X 100msec 00~99 00 Use this function when delay occurs in the line and
communication.
(ex. Mobile comm) does not work well.
874 DTMF ON time X msec 060~200 100 ----------
875 DTMF OFF time X msec 060~200 100 ----------
529 Call Service Clear
550 Memory clear Refer to Memory Clear Specification (P.145).
551 ROM check See Test Functions (P.136).
555 Scanner test See Test Functions (P.136).
556 Motor test 0 See Test Functions (P.136).
557 LED test See Test Functions (P.136).
558 LCD test See Test Functions (P.136).
561 KEY test See Test Functions (P.136).
628 H.V.P.S. check See Test Functions (P.136).
639 LSU test See Test Functions (P.136).
655 Cause Distinction Code of Call Service 3 See CALL SERVICE Troubleshooting Guide
(P.188).
677 FAN test See Test Functions (P.136).
710 Memory clear except History data Refer to Memory Clear Specification (P.145).
796 Attach sending image to sending
report
1: ON
2: OFF
1, 2 1
815 Sensor check See Test Functions (P.136).
852 Print test pattern See Test Functions (P.136).
853 Top margin X 0.5mm 01~11 06 ----------
854 Left margin X 0.5mm 01~11 06 ----------
856 Top margin (DUPLEX) X 0.5mm 01~11 06 ----------
870 Left margin (OPF) X 0.5mm 01~11 06 Only for KX-MB25** and DP-MB310
Code Function Set Value Effective
Range
Default Remarks