What to do if the Panasonic EP-MA70 Massager heads stop during operation?
If the massage heads of your Panasonic Massager stop moving during operation, and the controller displays flash and turn off, it might be due to excessive force applied to the massage heads. To resolve this, turn off the power switch, wait about 10 seconds, and then turn it back on. Also, ensure your back is not completely in contact with the backrest during use.
Why my Panasonic Massager won't turn on?
The Panasonic Massager might not operate if the power cord is disconnected, the power switch on the unit hasn't been turned on, or an Automatic program button or Manual Operation button hasn’t been pressed after pressing the power button. Ensure these steps are checked.
What to do if the massage heads stop during Panasonic EP-MA70 operation?
If the massage heads on your Panasonic Massager stop during operation, it could be due to excessive force applied to them. In this case, turn off the power switch, wait for about 10 seconds, and then turn it back on. Also, ensure your back is not completely in contact with the backrest.
How to fix Panasonic EP-MA70 Massager if it won't recline?
If you can't recline your Panasonic Massager, it might be due to an obstacle or excessive force exerted during operation. To resolve this, turn the power off, wait about 10 seconds, and then turn it back on before attempting to recline it again.
What to do if Panasonic Massager power won't turn on after massage?
If your Panasonic Massager sometimes won't turn on immediately after a massage has finished, wait at least 5 seconds after all movement has stopped before pressing the power button again.
Why is the height of massage heads different on Panasonic EP-MA70 Massager?
The different height of the left and right massage heads in your Panasonic Massager is normal because the unit uses an alternating tapping method. There is nothing wrong with the unit.
What to do if Panasonic EP-MA70 power cord is hot?
Stop using the Panasonic Massager immediately if the power cord or power plug is abnormally hot.
What to do if Panasonic EP-MA70 is damaged?
Stop using the Panasonic Massager immediately if the unit has been damaged.
Identifies and explains the functions of the main parts and components of the massage lounger.
Describes the layout and functions of the massage lounger's control panel buttons.
Explains the various displays and indicators on the massage lounger's control panel screen.
Step-by-step guide for safely removing the armrests from the massage lounger.
Instructions for removing external parts of the massage lounger, starting with armrests.
Details the process of removing the side cover, including handling hooks and screws.
Step-by-step guide to remove the top section of the rear cover.
Instructions for removing the bottom section of the rear cover.
Step-by-step procedure for adjusting the up/down sensor gear position.
Troubleshooting steps for when the motor does not operate.
Troubleshooting steps for when the massage mechanism block fails to move.
Diagnosis for when the massage mechanism block does not move, involving test modes.
Troubleshooting steps when the Ottoman lift unit does not operate.
Troubleshooting steps for issues with air bag operation or weak pressure.
Troubleshooting steps when the controller is on but shows no display.
Troubleshooting when controller buttons are pressed but no operation occurs.
Troubleshooting for controller display code F03, related to heater issues.
Troubleshooting for controller display code F06, related to heater issues.
Troubleshooting for controller display code F36, related to width sensor issues.
Troubleshooting for controller display code F80, related to width motor issues.
Troubleshooting for F34 error when Ottoman lift does not operate.
Troubleshooting for air bags not moving or having weak pressure.
Procedures to check the Main PCB for proper functioning and voltages.
Troubleshooting steps for when the electric reclining function does not operate.
Troubleshooting for controller displays that light briefly then turn off.
Troubleshooting for controller display codes F04/F05 concerning heater errors.
Steps to check heater, thermistor, and PCB when the heater is not hot enough.
Troubleshooting for controller display code F37, related to up/down sensor issues.
Troubleshooting for controller display code F81, related to up/down motor issues.
Troubleshooting for F35 error when reclining does not operate.
Troubleshooting for controller display code F31, related to body pressure sensor issues.
Troubleshooting for controller display code F38, related to intensity sensor issues.
Troubleshooting for controller display code F82, related to intensity motor issues.
Table detailing required air pressures for various body parts and strengths.
How to operate specific functions to check air pressure and interpret results.
Steps to prepare the system for entering secret modes.
Lists available secret modes and their corresponding codes for diagnostics and settings.
Details the heater error display (15) and related checks.
Checks for proper assembly and absence of sensor/motor failures.
Procedure to adjust the body pressure sensor.
Checks if the heater increases temperature properly within designated times.
Procedure to check the heater temperature using manual mode.
Lists various malfunctions, their phenomena, controller indications, and error codes.
To Next Page
General