Panasonic KX-FT931LA-B

57
KX-FT931LA-B
11.1.3. Service Function Table
Code Function Set Value Effective
Range
Default Remarks
501 Pause time X 100 msec 001~600 50 ----------
502 Flash time X 10 ms 01~99 70 ----------
503 Dial speed select 1: 10 pps
1: 20 pps
1, 2 1 ----------
514 Bell detection time X 100 msec 1~9 6 ----------
520 CED frequency select 1:2100Hz
2:1100 Hz
1, 2 1 See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not transmit/receive (P.82).
521 International mode select 1:ON 2:OFF 1, 2 1 See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not transmit/receive (P.82).
522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default when transmission
is complete.
523 Receive equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4 1 When the telephone station is far from the unit or recep-
tion cannot be performed correctly, adjust accordingly.
524 Transmission equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4 1 When the telephone station is far from the unit or trans-
mission cannot be performed correctly, adjust accord-
ingly.
544 Document feed position adjustment
value set
1: 3 mm
2: 4 mm
3: 5 mm
4: 6 mm
5: 7 mm
1~5 3 If it is difficult to feed documents, raise the set value. If
multi documents feed occurs, lower the set value.
550 Memory Clear See Memory Clear Specification (P.58).
551 ROM check See Test Mode(P.54).
552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See Test Mode(P.54).
553 Monitor on FAX communication select 1:OFF
2:PHASE B
3:ALL
1~3 1 Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
554 Modem test See Test Mode(P.54).
555 Scan check See Test Mode(P.54).
556 Motor test 0 See Test Mode(P.54).
557 LED test See Test Mode(P.54).
558 LCD test See Test Mode(P.54).
559 Document jam detection select 1:ON 2:OFF 1, 2 1 See Test Mode(P.54).
561 KEY test See Test Mode(P.54).
570 BREAK % select 1:61% 2:67% 1, 2 1 Sets the % break of pulse dialing according PBX.
571 ITS auto redial time set X number of
times
00~99 05 Selects the number of times that ITS is redialed (not
including the first dial).
572 ITS auto redial line disconnection time
set
X second 001~999 065 Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of
rings
01~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
590 FAX auto redial time set X number of
times
00~99 05 Selects the number of redial times during FAX commu-
nication (not including the first dial).
591 FAX auto redial time disconnection time
set
X second 001~999 065 Sets the FAX redial interval during FAX communication.
592 CNG transmit select 1:OFF
2:ALL
3:AUTO
1~3 2 Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialing is performed. OFF:
CNG id not output at phase A. Refer to Sometime
there is a transmit problem (P.80).
593 Time between CED and 300bps 1:75 msec
2:500 msec
3:1 sec
1~3 1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit/receive (P.82). Refer to Receive
Problem(P.81) and The unit can copy, but cannot
transmit/receive (P.82).
594 Overseas DIS detection select 1:detects at
the 1st time
2:detects at
the 2nd time
1, 2 1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit/receive (P.82). Refer to Sometime
there is a transmit problem(P.80) and The unit can
copy, but cannot transmit/receive (P.82).